Graco 127649 Instructions Manual Download Page 4

        M0302

EN

B.1 WARNINGS

The following warnings are for the setup, use, grounding, and repair of this equipment.  The 

exclamation point symbol alerts you to a general warning and the hazard symbols refer to 

procedure-specific risks.  When these symbols appear in the body of this manual or on warn-

ing labels, refer back to these Warnings.  Product-specific hazard symbols and warnings not 

covered in this section may apear thoughout the body of this manual where applicable.

   

WARNING

EQUIPMENT 

MISUSE

!

Misuse can cause death 

or serious injury

Do not operate the unit when fatigued or un-

der the influence of drugs or alcohol.

Do not exceed the maximum working pres-

sure or temperature rating of the lowest rated 

system component.  See Technical Data in all 

equipment manuals.

Use fluids and solvents that are compatible 

with equipment wetted parts.  See Technical 

Data in all equipment manuals.  Read fluid 

and solvent manufacturer’s warnings.  For 

complete information about your material, 

request MSDS from distributor or retailer.  

Do not leave the work area while equipment 

is energized or under pressure.

Turn off all equipment when equipment is 

not in use.

Check equipment daily.  Repair or replace worn 

or damaged parts immediately with genuine 

manufacturer’s replacement parts only.

Do not alter or modify equipment.  Altera-

tions or modifications may void agency ap-

provals and create safety hazards.

Make sure all equipment is rated and approved 

for the environment in which you are using it.

Use equipment only for it intended purpose.  

Call your distributor for information.

Route hoses and cables away from traffic areas, 

sharp edges, moving parts, and hot surfaces.

Do not kink or over bend hoses or use hoses 

to pull equipment.

Keep children and animals away from work area.

Comply with all applicable safety regulations.

Toxic Fluid 

or Fumes 

Hazard

Toxic fluids or fumes can 

cause serious injury or 

death if splashed in the 

eyes or on skin, inhaled, or 

swallowed.

Read MSDS’s to know the specific hazards of 

the fluids you are using.

Store hazardous fluid in approved contain-

ers, and dispose of it according to applicable 

guidelines.

Prolonged contact with the treated product 

may cause skin irritation: always wear protec-

tive gloves during dispensing.

Summary of Contents for 127649













Reviews: