1. Turn the remote over.
2. Remove the battery compartment by pressing in on the tab
and then sliding the compartment out.
3. Install a Cr2025 battery (positive side up).
4. Put the battery compartment back in the remote.
+
LITHIUM BATTERY
CR2025
3V
+
LITHIUM BATTERY
CR2025
3V
Warnings and Precautions
Features
REMOVE BEFORE USE
PULL
Unit:
Remote:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol, located on back or bottom of the unit, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
This product utilizes a Class 1 laser to read Compact Discs. This laser Compact Disc Player is equipped with safety switches to avoid exposure when the CD door is open and the safety interlocks are defeated. Invisible laser radiation is present when the
CD Player's lid is open and the system's interlock has failed or been defeated. It is very important that you avoid direct exposure to the laser beam at all times. Please do not attempt to defeat or bypass the safety switches.
Any use of the controls or an adjustment to the procedures other than those specified herein may result in hazardous radiation.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE ARE NO USER-SERVICEABLE PARTS INSIDE. PLEASE REFER ANY SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Receiver complies with Part 15 of FCC rules when manufactured.These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Special Note
When placing your unit on a lacquered or natural finish, protect your furniture with a cloth or other protective material.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol, located on back or bottom of the unit, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
This product utilizes a Class 1 laser to read Compact Discs. This laser Compact Disc Player is equipped with safety switches to avoid exposure when the CD door is open and the safety interlocks are defeated. Invisible laser radiation is present when the
CD Player's lid is open and the system's interlock has failed or been defeated. It is very important that you avoid direct exposure to the laser beam at all times. Please do not attempt to defeat or bypass the safety switches.
Any use of the controls or an adjustment to the procedures other than those specified herein may result in hazardous radiation.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE ARE NO USER-SERVICEABLE PARTS INSIDE. PLEASE REFER ANY SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Receiver complies with Part 15 of FCC rules when manufactured.These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Special Note
When placing your unit on a lacquered or natural finish, protect your furniture with a cloth or other protective material.
DC 1.5V "AAA" x 3
(Not Included)
OPEN
OPEN
+
LITHIUM BATTERY
CR2025
3V
+
LITHIUM BATTERY
CR2025
3V
Power Source
Connect the AC plug to a 120v AC, 60Hz wall outlet.
AC Connection
Battery Compartment
Three (3) “AAA” size batteries can also be used to power and/or
to provide backup for the clock and alarm time for as follows:
1. Open the battery door by pushing on the tab, removing the
door.
2. Insert three (3) “AAA” batteries as shown. Alkaline batteries are
recommended for the longest playing time.
3. Place the battery door back on the compartment.
WARNING:
Danger of explosion if batteries are incorrectly replaced. Replace only with the same
or equivalent type.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium)
batteries.
• Replace the batteries when the sound becomes unstable or cannot be heard.
• When you are not going to use your unit for a long time, remove the
batteries to prevent damage from battery leakage and corrosion.
Remove the plastic protective battery cover.
1. Turn the remote over.
2. Remove the battery compartment by pressing on the tab
and sliding the compartment out.
3. Install a CR2025 battery (positive side up).
4. Replace battery compartment back in the remote.
Remote Battery Installation
Remote Battery
WARNING:
The button cell battery contains mercury, don't put in the trash. Recycle or dispose as
hazardous waste.
CAUTION:
Danger of explosion if battery is incorrectly replaced, Replace only with the same or
equivalent type.
EQ BUTTON
BOTÓN EQ
BOUTON EQ
REPEAT BUTTON
BOTÓN REPEAT
BOUTON REPEAT
BAND BUTTON
BOTÓN BAND
BOUTON BAND
PROG/MEM BUTTON
BOTÓN PROG/MEM
BOUTON PROG/MEM
M+ BUTTON
BOTÓN M+
BOUTON M+
CLK ADJ/DISPLAY BUTTON
BOTÓN CLK ADJ/DISPLAY
BOUTON CLK ADJ/DISPLAY
MOUNTING BRACKET
SOPORTE DE INSTALACIÓN
SUPPORT D' INSTALLATION
12 V DC JACK
DC JACK DE 12V
FICHE 12V C.C.
POWER BUTTON
BOTÓN POWER
BOUTON POWER
TIMER BUTTON
BOTÓN TIMER
BOUTON TIMER
SKIP TUNE DN BUTTON
BOTÓN SKOP TUNE DN
BOUTON SKIP TUNE DN
TUNING BUTTON
BOTÓN TUNING
BOUTON TUNING
PLAY/PAUSEBUTTON
BOTÓN PLAY/PAUSE
BOUTON PLAY/PAUSE
STOP BUTTON
BOTÓN STOP
BOUTON STOP
FUNCTION BUTTON
BOTÓN FUNCTION
BOUTON FUNCTION
OPEN/CLOSE BUTTON
BOTÓN OPEN/CLOSE
BOUTON OPEN/CLOSE
BATTERY COMPARTMENT
COMPARTIMENTO DE PILAS
COMPATIMENT Á PILES
SKIP TUNE UP BUTTON
BOTÓN SKOP TUNE UP
BOUTON SKIP TUNE UP
M
- BUTTON
BOTÓN M
-
BOUTON M
-
REMOTE CONTROL
Control Remoto
Contrôle Éloigné
120V AC/60 Hz
POWER
OPEN/CLOSE
MUTE
FUNCTION
BAND
TIMER
SKIP FB/
TUNE DN
SKIP FF/
TUNE UP
PLAY/PAUSE
VOL
VOL
STOP
PROG/MEM
REPEAT
CLK ADJ/
DISPLAY
EQ
BAND BUTTON
BOTÓN BAND
BOUTON BAND
MUTE BUTTON
BOTÓN MUTE
BOUTON MUTE
OPEN/CLOSE BUTTON
BOTÓN OPEN/CLOSE
BOUTON OPEN/CLOSE
POWER BUTTON
BOTÓN POWER
BOUTON POWER
FUNCTION BUTTON
BOTÓN FUNCTION
BOUTON FUNCTION
TIMER BUTTON
BOTÓN TIMER
BOUTON TIMER
SKIP FF/TUNE UP BUTTON
BOTÓN SKIP FF/TUNE UP
BOUTON SKIP FF/TUNE UP
VOLUME
+ BUTTON
BOTÓN VOLUME
+
BOUTON VOLUME
+
PROG BUTTON
BOTÓN PROG
BOUTON PROG
BATTERY COMPARTMENT
COMPARTIMENTO DE PILAS
COMPATIMENT Á PILES
CLK ADJ/DISPLAY BUTTON
BOTÓN CLK ADJ/DISPLAY
BOUTON CLK ADJ/DISPLAY
VOLUME BUTTON
BOTÓN VOLUME
BOUTON VOLUME
PLAY/PAUSE BUTTON
BOTÓN PLAY/PAUSE
BOUTON PLAY/PAUSE
SKIP FB/TUNE DN BUTTON
BOTÓN SKIP FB/TUNE DN
BOUTON SKIP FB/TUNE DN
M+ BUTTON
BOTÓN M+
BOUTON M+
REPEAT BUTTON
BOTÓN REPEAT
BOUTON REPEAT
EQ BUTTON
BOTÓN EQ
BOUTON EQ
STOP BUTTON
BOTÓN STOP
BOUTON STOP
POWER
OPEN/CLOSE
MUTE
FUNCTION
BAND
TIMER
SKIP FB/
TUNE DN
SKIP FF/
TUNE UP
PLAY/PAUSE
VOL
VOL
STOP
PROG/MEM
REPEAT
CLK ADJ/
DISPLAY
EQ
