background image

5 Configuration Mode Introduction 

5.5 MSPI 

 

UG290-2.3E 

58(87) 

 

Connection Diagram for MSPI Configuration Mode 

The connection diagram for configuring Gowin FPGA products through 

MSPI is shown in Figure 5-40. 

Figure 5-40 Connection Diagram for MSPI Configuration Mode

 

FPGA

                       

                               
 FASTRD_N

                                MCLK

                             MCS_N

                                     MI

                                    MO

SPI Flash

CLK

CS_N

DOUT

DIN

 

Note! 

The figure above shows the minimum system diagram for the MSPI MODE. The value of 
the MSPI MODE is "010" (GW1N(R)) and “000” (GW2A(R) ). The other fixed pins are 
shown in Figure 5-1. The FASTRD_N pin can remain floating in MSPI mode if the clock 
frequency is less than 30 MHz. 

The connection diagram for programming data to external Flash is 

shown in Figure 5-41. The connection diagram for programming external 
Flash via the SSPI interface is shown in Figure 5-36. 

Figure 5-41 Connection Diagram of JTAG Programming External Flash 

FPGA

                     

TDI                       MCLK

TCK                   MCS_N

TMS                           MI

TDO                         MO

JTAG PORT

Flash

CLK

CS_N

DOUT

DIN

4

.7

K

 

Note! 

The figure above shows the minimum system diagram of programming external Flash via 
JTAG. The connection for the other fixed pins is shown in Figure 5-1 

Gowin FPGA products usually only support one time automatic MSPI 

configuration after power up. The GW1N (R)-9, GW2A (R)-18, and GW1NS 
series products are improved: GW2A (R)-18 series FPGA support retrying 
configuration once; GW1N (R)-9 and GW1NS FPGA support retrying 

Summary of Contents for GW2AR-18


































































































Reviews: