USING YOUR DEVICE
PRODUCT SPECS
USING YOUR DEVICE
HOW TO OPERATE
1)
Plug into the AC plug into
110/120v
socket ou
t
let.
2)
Press the power switch (11) on the side of motor base to the “I” position and
make sure the juice container is in position.
3)
Place an orange into slicing compartment (4) with top of orange facing left side
of compartment (Figure 1). Lower lid (1) to cut orange through centre. Excess juice
will run into juice container (8).
4)
Place orange halves on cones one at a time. Remember, pressure on both
cones simultaneously will begin operation.
5)
Place another orange in the slicing compartment (4).
6)
Lower lid (1) and, using both hands on either side of the lid, apply firm pressure.
This will start the juicing operation and cut the whole orange in half. Juice will flow
into container (8) below.
7)
The appliance will not operate by pressure on one cone (3)
,
only
when
both
cones
a
re
loaded with fruit.
8)
When halves are fully juiced, discard peel and repeat steps 5
and
6 until the
.
juice container (8) is full (approximately 500ml).
9)
Do not fill above the max. fill line.
10)
Slide out the juice container (8) to serve the juice.
11)
The removable sleeve (9) will strain the excess pulp and any pips from the
juice. If your prefer a higher fib
e
r
drink simply remove the sleeve. The drip tray
(10) will catch any juice remaining in the juicing chamber (8).
12)
It is recommended to rinse the cones (3) and juicing chamber (8) periodically
when preparing large quantities of oranges. If the juicer stops operating during
juicing, remove the cones (3) and rinse the juicing chamber (5) to remove excess
pips which may lodge underneath the cones (3) and prevent the unit from operat-
ing.
DISASSEMBLING
1)
Switch off the appliance and disconnect from supply before changing accesso-
ries or approaching parts that move in use
.
2)
Slide out juice container (8) and drip tray (10)
3)
To remove lid (1), open fully and apply pressure with thumbs as shown in
(Figure 2). Lid (1) will unclip from the juicing chamber together.
4)
To prevent juice from dripping, remove the cones (3) and juicing chamber (5)
together, operating the front lever (13)
5)
Hold motor base (7) with one hand, and with the other grasp the juicing
chamber (5) at the front and pull up over the drive shafts (6). The cones (3) will lift
off with the juicing chamber (5) as shown in (Figure 3).
6)
The cone (3) may also be removed separately from the juicing chamber (5) by
simply lifting them off the drive shafts (6).
7)
The juice drip tray (10) simply slides out for cleaning.
REASSEMBLING
1)
Replace the juicing chamber (5) onto the motor base (7) by sliding the protrud-
ing lugs at the back of the juicing chamber into the slots at the back of the motor
base as shown in Figure 4.
2)
Place cones (3) onto drive shafts (6).
3)
Place the lid (1) in its original location.
4)
Slide the drip tray (10) into position along guide rails, clipping rear tab into
position.
6
7
5)
The juice container (8) will then slide into position for storage.
No. Description
1.
Lid with cutting blade
2. Lid locating rods
3. Juicing cones with strainer baskets
4. Slicing compartment
5. Juicing chamber
6. Drive shafts
7. Motor base
8. Juice container
9. Pip and pulp sieve
10. Removable juice drip tray
11. On/off power switch
12. Cord storage compartment
13. Front disassembly lever