manualshive.com logo in svg

Goulds A-C 2000 Series, Instruction Manual

Share
Download
Goulds A-C 2000 Series Instruction Manual Download Page 5

5

Safety terminology and symbols

About safety messages

It is extremely important that you read, understand, and follow the safety messages and regulations carefully 

before handling the product. They are published to help prevent these hazards:

• Personal accidents and health problems

• Damage to the product

• Product malfunction

Hazard levels

Hazard categories

Hazard categories can either fall under hazard levels or let specific symbols replace the ordinary hazard 

level symbols.

Electrical hazards are indicated by the following specific symbol:

ELECTRICAL HAZARD:

These are examples of other categories that can occur. They fall under the ordinary hazard levels 

and may use complementing symbols:

• Crush hazard

• Cutting hazard

• Arc flash hazard

Hazard level

Indication

DANGER:

A hazardous situation which, if not avoided, will result in death or serious 

injury.

WARNING:

A hazardous situation which, if not avoided, could result in death or 

serious injury.

CAUTION:

A hazardous situation which, if not avoided, could result in minor or 

moderate injury.

NOTICE:

• A potential situation which, if not avoided, could result in

undesirable conditions

• A practice not related to personal injury

Summary of Contents for A-C 2000 Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands