manualshive.com logo in svg

Gossen MetraWatt MAVOMASTER, Operating Instructions Manual, Page: 42 / 56

Share
Download
Gossen MetraWatt MAVOMASTER Operating Instructions Manual Download Page 42

 

11 

Service Notes 

The  instrument  does  not  require  any  special  maintenance  if  used  in  accordance  with  the  operating 
instructions.  
 

▪

 

If  the  outside  of  the  device  becomes  contaminated  during  use,  clean  the  surface  of  the 
housing with a slightly moistened cloth. Avoid the use of cleansers, abrasives and solvents. 

 

▪

 

Make sure that the light receiver doesn’t become dusty, dirty or scratched because this can 
affect measurement accuracy. 

 
If at any time your instrument doesn’t function to your full satisfaction, send it to: 
 

GOSSEN Foto- und Lichtmesstechnik GmbH

 I Lina-Ammon-Str. 22 I D-90471 Nuremberg I 

Germany 
Phone: +49 911 800621-0 I Fax: +49 911 800621-29 I e-mail: [email protected] 
 
www.gossen-photo.de  
 
Customers outside of Germany are requested to contact their authorized dealer, whose address can 
be found on our website at www.gossen-photo.de. 
 
 

 

Summary of Contents for MAVOMASTER

























































Reviews:

No comments