Gorilla Playsets 1500BWF Manual Download Page 169

Page: 169 / 178

5/16" X 2-1/2" HEX BOLT

5/16" WASHER

2 X 4 X 28-9/16" CENTER POST

5/16" T-NUT

#8 X 2-1/2" WOOD SCREW

5/16" WASHER

5/16" x 4-1/2" HEX BOLT

2 X 6 X 70"
REAR PANEL SUPPORT
(OFFSET DOWN)

STEP 2A: REAR PANEL SUPPORT

1: PLACE THE 2 X 6 X 70" REAR PANEL SUPPORT ON THE REAR OF THE CORNER POSTS. THE

CENTER HOLE IN THE REAR PANEL SUPPORT MUST BE OFFSET DOWN.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE HOLES OF THE REAR

PANEL SUPPORT TO THE T-NUTS INSTALLED ON THE CORNER POSTS.

3: PLACE THE CENTER POST INSIDE THE REAR PANEL SUPPORT AT THE REAR OF THE

PLAYSET. LINE UP THE HOLE IN THE CENTER POST WITH THE CENTER HOLE IN THE REAR

PANEL SUPPORT.

4: FASTEN THE CENTER POST TO THE RAILINGS WITH 5/16" X 2-1/2" HEX BOLTS AND 5/16"

WASHERS AT THE TOP.

5: SQUARE THE CENTER POST TO THE DECK AND SECURE THE BOTTOM OF THE CENTER

POST TO THE BOTTOM PANEL BOARD WITH #8 X 2-1/2" WOOD SCREWS.

Summary of Contents for 1500BWF



















































































































































































Search results

Summary of Contents for 1500BWF

Reviews:

Related manuals for 1500BWF

Brands by name

Popular brands

Gorilla Playsets 1500BWF, Manual

Search results

Summary of Contents for 1500BWF

Reviews:

Related manuals for 1500BWF

Brands by name

Popular brands