Gorilla Playsets 1500BWF Manual Download Page 154

Page: 154 / 178

Some playsets have a Ladder, Rock Wall or Ramp here. If any of these items are here then this kit has

extra slats to fill up the sides of this opening.

Some playsets have a Tire Swing Beam

attached here.

For those playsets the panel slat steps

in this manual outline how to arrange

the panel slats around where the Tire

Swing Beam is attached.

Some playsets have a Tube Slide here along with a rear mounted Ladder. If the playset has a Tube

Slide here then this kit does not

have extra slats to fill up the spaces between the existing slats.

REAR OF

FORT

REAR OF

FORT

rear mounted Ladder

Plastic Sunburst

(included with playset

NOT with 1531 kit)

Plastic Sunburst

(included with playset

NOT with 1531 kit)

Summary of Contents for 1500BWF



















































































































































































Search results

Summary of Contents for 1500BWF

Reviews:

Related manuals for 1500BWF

Brands by name

Popular brands

Gorilla Playsets 1500BWF, Manual

Search results

Summary of Contents for 1500BWF

Reviews:

Related manuals for 1500BWF

Brands by name

Popular brands