background image

50
3909

•  The appliance may only be connected by an authorized skilled technician.
•  Electric system protection should comply with all relevant regulations. 
•  The connection clips can be accessed when the connection clip covers are opened / 

removed. 

•  Before connecting the appliance, make sure the voltage indicated on the rating plate is 

consistent with the voltage in your home circuit.  

•  The rating plate with basic information is attached on the lower side of the hob. 
•  The electric circuit should also include an omnipolar switch that will separate the 

appliance from the mains, if required, with at least 3 mm of distance between contacts. 
Suitable devices include fuses, current protection switches, etc. 

•  The connection should be selected according to the installation possibilities with 

regard to current and fuses.

•  Given the protection from the risk of fi re, appliances of this type may be installed in 

a worktop next to a piece of kitchen furniture that is taller than the appliance (when 
installed); however, in this case, a kitchen furniture element must be installed on the 
other side, adjacent to the appliance.

•  The current conducting and isolated parts must be protected from any possibility of 

direct contact.

WARNING!

•  Before any intervention, disconnect the appliance from the power mains. Connect the 

appliance in compliance with the electric connections diagram supplied; make sure the 
relevant network voltage is observed! The ground wire (PE) should be connected to 
the clip indicated by the earthing symbol. 

•  The mains cable should be fed through the fastening clip which protects it from being 

accidentally pulled out. 

•  After connecting the appliance, turn on all cooking zones / heaters for approximately 

three minutes to make sure they are operating correctly. 

Important warnings

‘’ The appliances are suitable for photovoltaic electrical 
power under the condition that electrical voltage will 
be 220VAC - 240VAC with semi tonic frequency 50Hz 
in order the appliance to operate properly (alternative 
a generator can be used with the same technical 
characteristic).’’ 
•  Incorrect connection may destroy parts of the appliance, 

making the warranty void.

•  Before connecting the appliance, make sure the voltage 

indicated on the rating plate is consistent with the 
voltage in your home network. Connection voltage 
(230 V through N) should be checked by a qualifi ed 
technician using a corresponding measuring device!

Connection diagram

16

CONNECTING THE APPLIANCE TO 
THE POWER MAINS

Summary of Contents for INFINITY GW6NINB

























Reviews: