Instructions for use, installation and connection
118
Instructions for installation and connection
Safety precautions for the technician
•
Installation may be carried out only by qualified personnel.
•
The electric installation shall be equipped with a safety
device, able to disconnect the appliance from mains in all
wires, with the distance between contacts of not less than 3
mm in open position. Good protection is provided by the LS-
switches and/or fuses.
•
The connection may be carried out by rubber mains lead
(type HO5RR-F with green/yellow earth wire), PVC insulated
mains lead (type HO5VV-F with green/yellow earth wire) or
other cables of equal or better quality.
•
Distance between the cooktop and the kitchen hood must be
at least the distance, indicated in the instructions for use of
the kitchen extraction hood.
•
Panels, glue and furniture lining from artificial materials,
adjacent to the appliance must be temperature resistant
(>75°C), otherwise they might be deformed.
•
Mains lead behind the cooker must be placed in such
manner to avoid touching the back panel of the cooker
because of the heat it develops during operation.
•
Remove any packaging materials (foils, artificial foam, nails,
etc.) from the reach of children, because they represent
potential danger. Children may swallow small parts, or
suffocate with foils.
,
Leveling the appliance and extra support
(only with certain models)
The height of the cooker with the support is 90 cm, and
without support it is 85 cm. Left and right side of the support is
equipped with two wheels to facilitate relocation. In the front
part, on both sides there are two adjustable screws, used to
level the cooker and adjust its upper edge in line with the
adjacent kitchen furniture.
Adjustable legs are accessible when the drawer is pulled out.
Adjust the position of the cooker by turning the legs in one
direction or another. Adjustable legs will be turned easier if the
appliance is somewhat lifted up and tilted.
Additional support may be removed by unscrewing the four
screws holding it to the bottom of the cooker. In such case
relocate the
Some cookers are equipped with four adjusting screws (two in
front and two at the back), used for leveling the appliance or
adjusting its heights to match the adjacent furniture.
Electric connection
Open the connection box using the screwdriver, as
shown by the drawing on the cover.
Connection to the mains power can be done only by
the authorized service center or by qualified
personnel!
Wrong connection may damage the parts of appliance and
render your warranty viod!
Connecting voltage of the user’s installation (230 V against N)
must be verified by qualified electrician using the appropriate
tester.
Connector bridges must be positioned in accordance with
the installation connection!
•
Prior connecting the appliance, check whether the voltage of
the rating plate corresponds to the actual voltage of home
installation.
•
Length of the power lead must be at least 1.5 m so that the
appliance can be connected to power before pushing it
against the wall.
•
Length of the earthing lead must be longer than the others,
so that it is strained later than the tension power leads in
case of accidental pullout from the socket.
Procedure
•
Using the screwdriver open the connection box cover at the
back of the appliance. You can do so by releasing two
catches, as shown on the connection box cover.
•
Power cable must be guided through the relief device,
protecting it from pulling out. If the relief device has not been
fixed yet, fix it in such way to hook the power cable to the
device housing at one end.
•
Now connect the power cable in accordance to
one
of the
options shown on the figure. In case of different installation
voltages, the connection bridges should be rearranged
accordingly!
•
Tighten the relief device and close the connection box cover.
NOTE:
In some connection boxes the connector bridges are placed
between contacts 4 and 5, and in the others they are stored at
a designated place within the box. These boxes have the
connection screws already in open position so they need not
be unscrewed. During the tightening procedure you will hear a
faint “click”, meaning that the tightening screw should be
fastened tightly all the way.
230V 3~
PE
L3
L2
L1