background image

Eng. Edition 1.0  2004, Nov. 

3

1.2 Technical data. Dimensions 

 

Heat output, max.  ___________________ 

approx. 20 kW  

Heat output, min.  ___________________ 

approx. 13 kW 

Output levels 

___________________ 

65 %, 100 % 

Combustion efficiency          ___________    approx. 95 %  
Combustion air consumption ___________    approx. 30 – 40 m

3

/h 

Weight ___________________________ 

approx. 13 kg 

Power supply 

    _________________    230 V 50 Hz 

Power consumption (ignition)__________ 

400 W 

Power consumption (operation)_________ 

40 W 

Fuel        ___________________________ 

Wood pellets:  

 6 or 

 8 mm 

 

 

 

 

       

 

  max. length 30 mm 

 

Dimensions (outside the boiler): 
 Depth 

 

__________________________ 300 

mm 

 

Width    _________________________ 

225 mm 

 

Total height ______________________  520 mm 

 
Dimensions, combustion chamber tube in the boiler: 
 Length 

_________________________  205 

mm 

 Diameter 

_______________________  155 

mm 

 
Recommended exhaust gas values: 
 CO

2

  ___________________________ 

10 – 13 % 

 

CO   ___________________________ 

< 300 ppm 

 
Recommended exhaust gas temperature _ 

180 ±20ºC 

(Measured directly after the boiler) 
 

Summary of Contents for PELLX
























Reviews: