background image

 

11

 

For each display, users can define which area of the input video is to be displayed. Fundamentally, 

setup the X Total and Y Total first, and then define the upper-left (X Start, Y Start) and bottom-right (X 
End, Y End) corners for each display channel. The control panel to achieve this goal is as shown. 

 
 

        This  small  area  will  demonstrate  the  resulting  selection  of  the  input  video  to  be  display  for  the 

selected output channel! 

 

       

Original Input Video

” shows the resolution information of the input video to each output channel, 

and it will vary depending upon the input video. 

 

Selected Area

” shows the information of the selected area to be displayed. The numbers will vary 

according to different settings. 

 

       

Output Resolution

” Section 

 

Setup the output resolution for individual output channel. Notice that each display can run at different 
resolutions to adapt more situations coming from different panels. 

 

Check 

Capture Mode Enable

” will enable parameters effective. If users disable this selection, each 

output channel will display simply the full display of the input video. 

 

Check 

Auto Apply Settings

” will automatically load the new settings into processor! 

 

Clicking on 

Update Status

” will keep the information of the input video updated! 

 

Clicking  on 

Update  Apply  Settings

”  will  load the  parameters  into  processor! While  “

Auto  Apply 

Settings

” is checked, users do not worry about settings changes. 

 

        Define XTotal, YTotal, Upper-left X, Y point coordinates using scroll bars or manually keying in this 

section accordingly! This section will roughly define these quantities which need for each individual 
channel. The resulting capture area corresponds to the input video will be illustrated in          . 

 

       

Fine Tune by Percentage

” will provide the alternative to further adjust the position and area defined 

in          . 

 

               

For outward extension                         For inward shrink 

 

By percentage, users need to determine what will be the reference. There are two choices for this 
part: 

Specified  Area

”  and  “

Full  Input

”.  Normally,  “

Specified  Area

”  will  work  more  appropriately 

while users are dealing with panel masking, because the overlapped masking area will be close the 
specified area instead of full input video!   

 

       

Fine Tune by Pixel

” offers similar approach to adjust the position and area of the output channel! 

 

The idea behind this section is the same to 

Fine Tune by Percentage

”. The difference is that the 

adjustment is based on pixel! Users can therefore adjust the output channel area pixel wise. 

 

Summary of Contents for VW-1312
















Reviews: