27
e
D
tail of the converter installation.
The converter can be installed on a DIN
guide with
(
6 elements
)
simply pressing it.
To extract the converter from the DIN guide,
use a plain screwdriver to lever the flange as
shown on the picture.
Install the converter in a dry, protected place.
DIN 46277
To install the converter directly on the wall, drill two holes
of Ø6mm. and insert the wallplugs. Fix the transformer
with the specified screws.
escription of the converter.
D
DESCRIPTION
INSTALLATION
DIN rail latch release
Autodiagnostic LEDs
Configuration dip switch
PLUS
connection block
R5
connection block
27
e
D
tail of the converter installation.
The converter can be installed on a DIN
guide with
(
6 elements
)
simply pressing it.
To extract the converter from the DIN guide,
use a plain screwdriver to lever the flange as
shown on the picture.
Install the converter in a dry, protected place.
DIN 46277
To install the converter directly on the wall, drill two holes
of Ø6mm. and insert the wallplugs. Fix the transformer
with the specified screws.
escription of the converter.
D
DESCRIPTION
INSTALLATION
DIN rail latch release
Autodiagnostic LEDs
Configuration dip switch
PLUS
connection block
R5
connection block
28
CONFIGURATION
e
D
scription of the configuration dip switch.
The
SW1
configuration dip switch is located in the upper
right part of the module.
Column encoder
(Master)
:
Activate this mode if you have
PLUS
door panels before the
converter
and
VISTA PLUS
monitors (without door panel) after the
converter
(see page
26).
Loads the
VISTA PLUS
installation with a
communications resistor.
Set to
ON
position only if you do not have
the
VISTA PLUS
door panel in the
installation.
* Factory default
Set to ON to program the column.
This function should only be used if the module is being used as
column
encoder (see page 26).
Once the programming progress is finished return the switch to
OFF position.
The programming steps are described on page 29.
The operation mode of the converter is defined according to the dip switch 2 and 3
combinations:
Column encoder
(Slave):
Activate this mode if you have
PLUS
door panels before the
converter
and
VISTA PLUS
monitors and door panels after the
converter
. (See page 26).
Exchange interface:
Activate this mode if placing a
PLUS
porter's exchange in a
VISTA PLUS
installation (see page 25).
e
D
scription of the configuration jumpers.
Auto
On
On
Off
Off
Off
JP1
JP2
JP4
End of line resistor (Only in porter´s exchange interface mode).
Set to AUTO if the porter's exchange is connected through a D4L-R5
video distributor (recommended), if doing without this element, set to
the OFF position.
End of line resistor (Only in column encoder mode).
Set to Off in all converters except the last one (end of the coaxial
cable).
To be handled exclusively by Golmar personnel.
Set always to Off.
28
CONFIGURATION
e
D
scription of the configuration dip switch.
The
SW1
configuration dip switch is located in the upper
right part of the module.
Column encoder
(Master)
:
Activate this mode if you have
PLUS
door panels before the
converter
and
VISTA PLUS
monitors (without door panel) after the
converter
(see page
26).
Loads the
VISTA PLUS
installation with a
communications resistor.
Set to
ON
position only if you do not have
the
VISTA PLUS
door panel in the
installation.
* Factory default
Set to ON to program the column.
This function should only be used if the module is being used as
column
encoder (see page 26).
Once the programming progress is finished return the switch to
OFF position.
The programming steps are described on page 29.
The operation mode of the converter is defined according to the dip switch 2 and 3
combinations:
Column encoder
(Slave):
Activate this mode if you have
PLUS
door panels before the
converter
and
VISTA PLUS
monitors and door panels after the
converter
. (See page 26).
Exchange interface:
Activate this mode if placing a
PLUS
porter's exchange in a
VISTA PLUS
installation (see page 25).
e
D
scription of the configuration jumpers.
Auto
On
On
Off
Off
Off
JP1
JP2
JP4
End of line resistor (Only in porter´s exchange interface mode).
Set to AUTO if the porter's exchange is connected through a D4L-R5
video distributor (recommended), if doing without this element, set to
the OFF position.
End of line resistor (Only in column encoder mode).
Set to Off in all converters except the last one (end of the coaxial
cable).
To be handled exclusively by Golmar personnel.
Set always to Off.
f
3,5 x 50
DIN-7971
f
3,5 x 50
DIN-7971
