golmar KIT SOUL S4110 ART 1 G2+/T-ART G2+ Instruction Manual Download

Page: 6 / 28

Installation

The door panel has been designed to withstand diverse environmental conditions. It is however advisable to take

extra precautions to prolong its service life, such as locating it in a covered area.

For correct installation: (locate the top of the door panel at a height of 1.65m).

1. Remove the metal front piece of the door panel by loosening the bottom screw with the Allen key supplied. On

the back of the front piece, you will find the button personalisation label.

2. Remove the screws that secure the

Illumination module

3. Present the door panel to the wall, positioning the top at 1.65m. Pass the installation cables through the cable

grommet.

. Drill three 6mm holes at the indicated points ( ), see p. 5. Insert the plugs supplied and fix the door panel to the

wall using the screws supplied.

5. Connect the cables to the terminals following the instructions in the installation diagrams.

Before replacing the

and closing the door panel, perform the necessary settings (

illumination module

address door

panel

illumination module

, audio level setting, etc.), as indicated throughout this manual. Make sure that the

gasket is properly fitted.

Installation terminals ( )

BUS

CV-

CV+

AP+

AP-

BUS BUS

: communications bus (non-polarised).

CV CV

+: lock release output 12Vdc (maximum 270mA).

-: remote activation button connection.

Note: For correct

operation, the

’s address 1 must be connected to

terminal

the Bus.
IMPORTANT:

Installation with 2 access door panels and

AP button on both door panels, one of the door panels
must connect the AC lock release (instead of DC lock
release). SAR-12/24

required,

relay

a TF-104 transformer

see pages 24 to 25.

: potential-free relay output (maximum 6A/24V).

SOUL/1A PANEL

SOUL

ART

S 110

1 G2+ / T-ART G2+ AUDIO DOOR ENTRY SYSTEM KIT

Summary of Contents for KIT SOUL S4110 ART 1 G2+/T-ART G2+





























Search results

Summary of Contents for KIT SOUL S4110 ART 1 G2+/T-ART G2+

Reviews:

Related manuals for KIT SOUL S4110 ART 1 G2+/T-ART G2+

Brands by name

Popular brands

golmar KIT SOUL S4110 ART 1 G2+/T-ART G2+, Instruction Manual

Search results

Summary of Contents for KIT SOUL S4110 ART 1 G2+/T-ART G2+

Reviews:

Related manuals for KIT SOUL S4110 ART 1 G2+/T-ART G2+

Brands by name

Popular brands