Goldstar MVH1670ST Service Manual Download Page 30 | Manualshive

Page: 30 / 43

background image

7-19

(2) CHECKOUT PROCEDURES FOR RELAY.

- PROBLEM (A) -

Vent fan motor and oven lamp turn on without touching

START key when the door is closed.

Remove the mate connector of I/O
CON from the circuit board.
Does the unit still operate?

Replace the
circuit board

Replace
RELAY1, 12

NO

NO

YES

YES

GOOD

Defective
RELAY1, 12

- PROBLEM (B) -

Vent fan motor and oven lamp turn on When the door

is closed and START key is touched.

Measure the voltage at pin NO.
47, 50 of U01 or 48, 49, 51 of U01
Voltage reading: 0 Vdc

Replace the
circuit board

Defective

RELAY1, 12 or poor

connection of

RELAY1, 12

Replace

RELAY1, 12 or correct

the connection.

YES

NO

NO

YES

GOOD

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes

«
...
28
29
30
31
32
...
»

Summary of Contents for MVH1670ST












































Reviews:

No comments

Related manuals for MVH1670ST

Brand: Tappan Pages: 20

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 8

Brand: Maytag Pages: 13

Brand: Panasonic Pages: 38

Brand: Candy Pages: 160

Brand: Candy Pages: 103

Brand: Oster Pages: 16

Brand: Sears Pages: 15

Brand: Artusi Pages: 20

Brand: Daewoo Pages: 23

Brand: Daewoo Pages: 19

Brand: Kasanova Pages: 62

Brand: Palsonic Pages: 14

Brand: Progress Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands