Goldmund EPILOGUE 3 SIGNATURE User Manual Download

Page: 16 / 16

SPECIFICATIONS

Epilogue 3/4

Amplifier Analogue Input Impedance

: > 100 kOhms.

Amplifier maximum power

: 500 W Rms.

Bandwidth

•

Low Frequency Cutoff : < 22 Hz -3dB.

Drivers :

8 x 21 cm Velvet Kevlar proprietary drivers mounted 4x2 in inverted push-pull with

front speaker mounted backwards.

Electronic Crossover

: 3 separate frequencies (5 in Epilogue 4). Master level control.

Bass Load

: vent loading. 4 separately tuned flexible vents.

Size and Weight

•

Weight of one Epilogue 3/4 sub-woofer : 140 kg.

•

Size of an Epilogue 3/4 sub-woofer : 78 cm (H) x 52 cm (W) x 72 cm (D).

Full System

Size and Weight of the Full system :

•

Total Height of the full speaker : 2 meters.

•

Total Width of the full speaker : 52 cm.

•

Total Depth of the full speaker : 80 cm.

•

Total Weight of one full speaker : > 320 kg.

Summary of Contents for EPILOGUE 3 SIGNATURE

















Search results

Summary of Contents for EPILOGUE 3 SIGNATURE

Reviews:

Related manuals for EPILOGUE 3 SIGNATURE

Brands by name

Popular brands

Goldmund EPILOGUE 3 SIGNATURE, User Manual

Search results

Summary of Contents for EPILOGUE 3 SIGNATURE

Reviews:

Related manuals for EPILOGUE 3 SIGNATURE

Brands by name

Popular brands