background image

                   GoldenEar Technology

8

SuperSub XXL Manual

Auto-On/Standby or Always-On – 

Your subwoofer will turn on when it receives an input signal — eliminating the 

need for a power switch. If no signal is sensed for a period of time, the subwoofer will automatically switch off.
See “Powering Up the Subwoofer” section below for more details.

Powering Up the Subwoofer

Your SuperSub XXL subwoofer contains a built-in, active powered subwoofer section as well as an electronic 

crossover. Each SuperSub XXL subwoofer must be plugged into an electrical socket (use an unswitched outlet if 

possible) of the appropriate voltage (as indicated on the back of your unit) using the plug on the end of the 
black cord attached to the electronics module on the back of the subwoofer. The SuperSub XXL subwoofer has 

a special circuit which automatically turns the powered subwoofer section on when a signal is fed to the loud-

speaker and does not require an on/off switch. (When the Subwoofer is fi rst plugged in, the LED will fl ash for 
30 seconds while the sub conducts a self-test, initializing the software and hardware. After 30 sec, if there is no 

audio signal, the LED will turn off and the subwoofer will go into standby mode drawing a low amount of power 

while waiting for an audio signal.) 

The LED on the back panel will light up when a signal is sensed and the amplifi er will turn on. After you stop 

listening, it may take up to an hour for the amplifi er to actually turn off. (

Please note: In some instances, because 

of RF presence in your area, the LEDs may not turn off. However, this is nothing to be concerned about as the 
amplifi ers draw almost no power when they are idling.) 

Please note: It is normal to hear a slight pop from the 

subwoofer when the amp powers up.

NOTE: To prevent accidental damage to your subwoofer from overdriving the system, the subwoofer features an 

internal overload protection circuit, which will turn the subwoofer off or down when overdriven or overheated and 

will then resume normal operation after a few minutes.

Complete Home Theater Systems 

 

 

 

 

 

       

We strongly suggest that you use a matching GoldenEar Technology Left, Right, Center channel and 

Rear/Surround speakers to complete your GoldenEar home theater system.

9

Summary of Contents for SuperSub XXL

















Reviews: