background image

Compass™ Service Manual

GP600-SM

3

    RevA02062006

SPECIFICATIONS

WEIGHT

Base: includes frame, motors, wheels, seat receivers, and
shrouds

88 lbs.

Armrests with joystick

14 lbs.

Seat with headrest (without armrests)

34 lbs.

Batteries (each)

U1 = 24 lbs.
NF22 = 39 lbs.

Total weight with batteries

With U1batteries = 184 lbs.
With NF22 batteries = 214 lbs.

OVERALL DIMENSIONS

Length

With standard footrest = 38 1/2 in.
With extended footrest = 41 1/2 in. to 43 in.

Width (measured from outsides of tires)

24 1/2 in.

MAXIMUMS

Incline

Speed

5 mph

Load Capacity

300 lbs.

TURNING RADIUS

Without footrest = 15 in.
With standard footrest = 19 in.
With extended footrest = 22 in.

WHEEL SIZES

Drive wheels = 10 in. x 3 1/2 in.
Casters = 6 in. x 2 in.

SEAT DIMENSIONS

Standard seat cushion

18 in. x 18 in., 18 in. x 20 in., 20 in. x 20 in.

Adjustable armrest width (measured from outsides)

23 1/4 in. to 29 3/4 in.

Adjustable armrest-to-seat cushion height

8 in., 9 in., or 10 in.

Adjustable seat-to-floor height

With U1 batteries = 18 in. to 23 in.
With NF22 batteries = 20 in. to 23 in.

Adjustable seat back-to-floor height with U1 batteries
(Add 2 in. to each measurement if using NF22 batteries.)

Without headrest = 37 in. to 41 in.
With headrest unextended = 45 in. to 49 in.
With headrest extended = 50 in. to 54 in.

Adjustable footrest-to-floor height

5 in., 5 5/8 in., 6 1/4 in., 6 7/8 in., or 7 1/2 in.

ADJUSTABLE FOOTREST ANGLE

- 4° to 17°

CONTROLLERS

Integral OR Dynamic Shark; 60 amp programmable with
K10 or K11 lockout

CHARGER

Off board, 110 VAC 60 Hz 5 amp

COLORS

Candy Apple Red, Artic Blue, Hunter Green, Onyx

BATTERIES (recommended)

Two U1 (35 Ah) SLA, AGM, or Gel; OR two NF22 (55 Ah)

Summary of Contents for compass














Reviews: