Gold Note B-7 Ceramic User Manual Download Page 12

1

Read these instructions and store them.

2

Heed all warnings.

3

Follow the instructions.

4

Do not use this apparatus near water.

5

Clean only with a dry cloth.

6

Do not block the ventilation openings and install in accordance

with the manufacturer's instructions.

7

Do not install near heat sources such as radiators, heat

registers, stoves or other apparatus (including amplifiers) that
produce heat.

8

Do not defeat the safety purpose of the polarized or

grounding-type plug: a polarized plug has two blades with one
wider than the other.

A grounding type plug has two blades and a third grounding
prong.

The wide blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.

• Do not expose this apparatus to drips or splashes.

• Do not place any objects filled with liquids, such as vases, on
the apparatus.

• Do not install this apparatus in a confined space such as a
book case or similar unit.

• The apparatus draws nominal non-operating power from the
AC outlet with its POWER or STANDBY/ON switch not in the ON
position.

• The apparatus should be located close enough to the AC
outlet so that you can easily grasp the power cord plug at any
time.

• The main plug is used as the disconnect device, the
disconnect device shall remain readily operable.

• If the product uses batteries (including a battery pack or
installed batteries), they should not be exposed to sunshine, fire
or excessive heat.

• Caution should be taken when using earphones or
headphones with the product because excessive sound
pressure (volume) from earphones or head- phones can cause
hearing loss.

9

Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.

10

Only use attachments/accessories specified by the

manufacturer.

11

Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.

12

Unplug this apparatus during lightning storms or when

unused for long periods of time.

13

Refer all servicing to qualified service personnel only.

Servicing is required when the apparatus has been damaged in
any way (such as when the power cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture) and in any
case when the apparatus does not operate normallyor has been
dropped.

IMPORTANT SAFETY INFORMATION

11

Summary of Contents for B-7 Ceramic

















Reviews: