Gold Medal Shavatron 1020 Instruction Manual Download Page 16

 

 

 

 

© 2013 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of 
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website 
display, without its express written consent. 

 
 

WARRANTY 

Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to  
be free of defects in workmanship and material under normal use and service. Gold Medal 
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts, 
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and 
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. 
Except for “Perishable Parts” on specific machines, the above warranty applies for a period  
of two (2) years from the date of original sale to the original purchaser of equipment when 
recommended operating instructions and maintenance procedures have been followed. These 
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months. 

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR 
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, 
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE  
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE 
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or 
consequential damages. No claim under this warranty will be honored if the equipment covered 
has been misused, neglected, damaged in transit, or has been tampered with or changed in any 
way. No claim under this warranty shall be honored in the event that components in the unit at 
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty 
is effective only when electrical items have been properly attached to city utility lines only at 
proper voltages. This warranty is not transferable without the written consent of Gold Medal 
Products Co. 

The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, 
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., 
or their authorized distributor for the equipment. 

THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL 
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO 
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, 
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR 
REPLACEMENT OF PARTS. 

NOTE: This equipment is manufactured and sold for commercial use only. 

 

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 

gmpopcorn.com

 

 

Phone:  (800) 543-0862 

Fax:  (800) 542-1496 

 

(513) 769-7676 

 

(513) 769-8500 

Summary of Contents for Shavatron 1020

















Reviews: