Gold Medal 2169-00-100 Instruction Manual Download Page 7

 

 

Karmel Kool Table

 

Model No. 2169-00-100 

 

 

Page 7 

 

 

gmpopcorn.com

Electrical Requirements 

The following power supply must be provided (reference unit Data Plate for Wattage requirement):  

120 V~, 60 Hz 

 

 DANGER

 

Machine must be properly grounded to prevent electrical shock to personnel. 
Failure to do so could result in serious injury, or death. 
DO NOT immerse any part of this equipment in water.  
DO NOT use excessive water when cleaning. 
Keep cord and plug off the ground and away from moisture. 
Always unplug the equipment before cleaning or servicing. 
Make sure all machine switches are in the OFF position before plugging the 
equipment into the receptacle. 

008_051514 

 
A certified electrician must furnish sufficient power for proper machine operation and install any 
supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage 
requirements). We recommend this equipment be on a dedicated and protected circuit. Failure 
to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal 
Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of 
extension cords is not recommended due to safety concerns, and may cause sacrificed and/or 
reduced performance. Make sure cord is located to prevent a trip hazard or unit upset. Units with 
an IEC Power Cord - make sure the IEC cord is properly seated into the IEC receptacle before 
powering up the machine. 

Before You Plug In Machine 

1.

 

Make sure all machine switches are OFF before plugging equipment into receptacle. 

2.

 

Make sure wall outlet can accept the grounded plugs (where applicable) on the power 
supply cord. 

3.

 

The wall outlet must have the proper polarity. If in doubt, have a competent 
electrician inspect the outlet and correct if necessary. 

4.

 

DO NOT

 use a grounded to un-grounded receptacle adapter (where applicable). 

5.

 

Install unit in a level position. 

 

 

 

CAUTION

 

If the supply cord is damaged, it must be replaced by Gold Medal Products Co., 
its service agent or similarly qualified persons in order to avoid a hazard. 

039_080614 

 

 

 

Summary of Contents for 2169-00-100




















Reviews: