background image

 

3. Turn the stem’s lock nut in the reverse direction of the arrow to lock   

      it in place. 

4. Unscrew the knobs on the search coil and remove the knobs and   

    the connector. Insert the stem and align the holes on the search coil   

    bracket and the stem. Push the connector through the holes, then   

    replace and tighten the knobs. 

5. Insert the latch on the top of the handle into the assembly hole on   

    the bottom of the control box. Then slightly pull the handle in the   

    direction of IN on the handle to fix the latch in place. 

   

  Assembly

 

hole

                   

latch 

 

6. Insert the search coil cable plug into the five pin jack on the front   

    control box’s housing. 

Caution:   

 

The search coil cable plug fits into the connector  only one way. Do 

not force the plug or you could damage it. 

 

You  don’t  need  to  disassemble  the  stem  lock  nut.  In  case  you 

disassemble  it  carelessly,  place  the  washer  on  the  top  of  the  stem 

connected  with  the  handle  with  the  small  head  of  the  washer 

upwards. Then hitch the stem lock nut on the washer then tighten it 

to lock it in place. 

OPEN

IN

OUT

Summary of Contents for GC-1012

















Reviews: