Memory Function
The device is equipped with memory function for the panel setting. It will help remember the panel setting 3 second
after you set it. When starting up the flash next time, the panel setting will be the same as the status before
powering it off.
Tube Replacement
Shut down the power and remove the power cord before replacing the flash tube and wear insulated gloves. Then,
loosen the iron wire on the tube, keep a balanced hold on the two feet of the flash tube and pull out the old tube
gently. Take down the feet casing from the old tube and put it on the new one. Hold two feet of the new tube, and
target directly towards the two copper outlets, then push them slightly in. Twine the iron wire on the stainless steel
sheet to fix the flash tube.
- 29 -
- 30 -
Other Applications
Wireless Control Function
The flash unit is built in with a Wireless Control Port so that you can wirelessly adjust the power level
of the flash and the flash triggering.
To control the flash wirelessly, you need a FT-16 remote control set (on-camera and on-flash). Insert
its receive end into the Wireless Control Port on the flash and insert the transmit end into the camera
hot shoe. Settings made on the hotshoe-mounted transmit and receive ends will be
wirelessly communicated to the flash. Then you can press the camera shutter
release button to trigger the flash. You can also hold the transmit end at
hand to control your off-camera flash.
For full instructions on the use of FT series remote control, see its
user manual.
Sync Triggering
The Sync Cord Jack is a Φ3.5mm plug. Insert a trigger plug here and the flash will be fired synchronously with the
camera shutter.
●
Shut down the device immediately when it works abnormally and find out the reason.
●
Avoid sudden impacts and the lamp should be dedusted usually.
●
It’s normal for lamp being warm when in use. Avoid continuous flashes when it is not necessary.
●
Maintenance of all the flashes is up to our authorized maintenance department which can provide original accessories. Users can
replace the flash tube and modeling lamp provided by the manufacturer.
●
One year warranty period will be cancelled when any unauthorized maintenance is found.
●
If the product had failures or was wetted, it can be continuously used only after it is repaired by professionals.
●
Disconnect the power when doing maintenance work or cleaning.
●
New changes made to the specifications or designs may not be updated in this manual.
Maintenance
Technical Data
Model
Quicker600IIM
Quicker400IIM
Flash Mode
M/Multi/Hss(high-speed sync)
Guide Number in 1/1 full power
(
m ISO 100, using standard reector)
76
65
Flash Duration
(t0.1)
High-Speed Flash (speed) Mode
1/316s
－
1/28984s
1/416s
－
1/35086s
Stable Color Temperature Mode
1/316s
－
1/4246s
1/416s
－
1/4983s
Color
Temperature
Stable Color Temperature Mode
5600
±
200K
5600
±
200K
High-Speed Flash (speed) Mode
5400K~9000K
5400K~9000K
High-Speed Sync Flash (speed) Mode
4600K~5000K
4600K~5000K
POWER
600WS
400WS
Recycle Time
Approx. 0.05-0.9s
Approx. 0.05-0.7s
Output Level
M
1/128~1/1
Hss
1/16~1/1
Multi
1/128~1/8
Multi Flash
Yes
(
max. ash time: 99; max. ash frequency: 30)
Sync Mode
High-speed sync (up to 1/8000s)
,
rst curtain sync
,
second curtain
sync
Delay Flash
0.01~30s
MASK Function
√
Fan
√
Beeper
√
Modeling lamp
150W
Slave Trigger Model
S1/S2
Display Flash Duration
√
Display
High qualied LCD panel
•
Radio (2.4G) Transmission (X system)
Wireless Function
Slave unit
,
ON/OFF
Controllable Slave Units
16 groups
:
0~9
，
A,B,C,D,E,F
Transmission Range (approx.)
50m
Channel
32
:
1~32
Sync Triggering Mode
3.5mm sync line, PC sync socket
，
wireless control port
Dimension
Flash diameter
Φ
14CM, height of ash with handle 23CM,
length o f ash with lamp cover 41CM
Net Weight
Approx. 2.96Kg
