Go Power GPSW-1500 Owner'S Manual Download Page 13

GPSW-600/1500 

___________________________________________________________

 

13

 

 

When determining whether a microwave oven can be operated by the 1500 W 
inverter, remember that the power commonly advertised for microwave ovens is 
the cooking power (the power delivered to the food) not the power actually 
consumed by the microwave oven. The microwave oven will consume 40% to 
100% more than its advertised cooking power. Check the rating sticker on the 
back of the oven to determine its actual power draw. The 1500 W inverter will 
operate a small microwave oven (0.2 to 3.0 cubic foot capacity) that draws up to 
1800 watts. It will provide 10 to 15 minutes of cooking time, depending on battery 
capacity. Some induction motors used in refrigerators, freezers, pumps, and 
other motor-operated equipment require very high surge currents to start. The 
power inverter may not be able to start some of these motors even though their 
rated current draw is within the power inverter. 
 
If the motor refuses to start, observe the battery voltage indicator while trying to 
start the motor. If the battery voltage indicator drops below 11 volts while the 
inverter is attempting to start the motor, this may be why the motor won’t start. 
Make sure that the battery connections are good and the battery is charged, but 
if the voltage still drops below 11 volts, you may need to use a larger battery. 

 

6.2 Input voltage: 

The power inverter will operate from input voltage ranging 10-15V (GPSW-600W-
12V ver.) and 10 V – 16 V (GPSW-1500-12V ver.) or 20 V-32 V (24 V ver.) If the 
voltage drops below 10.5 V (12 V ver.) or 21 V (24 V ver.), an audible low battery 
warning will sound and the voltage indicator will be in the lower red zone. The 
power inverter will shut down if the input voltage drops below 10 V (12 V ver.) or 
20 V (24 V ver.). This protects your battery from being overly discharged. 
 
The power inverter will also shut down if the input voltage exceeds 16 V (12 V 
ver.) or 32 V (24 V ver.). This protects the inverter against excessive input 
voltage. The voltage indicator will be in the upper red zone. Although the power 
inverter incorporates protection against over voltage, it may still be damaged if 
the input voltage is allowed to exceed 20 V (12 V ver.) or 40 V (24 V ver.). 
 
 

7. Troubleshooting 
 
7.1 Common problems 

Television interference: Operation of the power inverter can interfere with 
television reception on some channels. If this situation occurs, the following steps 
may help to alleviate the problem. 
 
• Make sure that the chassis ground lug on the back of the power inverter is 
solidly connected to the ground system of your vehicle, boat or home. 
 
• Do not operate high power loads with the power inverter while watching 
television. 

Summary of Contents for GPSW-1500





















Reviews: