GMP PROTOPIC-540 QUATRO SLIT User Manual Download Page 38 | Manualshive

Page: 38 / 51

background image

TROUBLESHOOTING

SYMPTOMS

CASE OF TROUBLES

TROUBLESHOOTING

When using the Rewinder

1. If the Rewinder tension is strong.

1. Please rotate the Rewinder tension control handle to the left side.

not good.

The rewinder tension will decrease

2. If the Rewinder tension is weak.

2. Please rotate the Rewinder tension control handle to the right side.

The rewinder tension will increase

If the roller temperature is

1. if the sensor is defective

1. Please ask to a supplier.

not working well

2. If foreign substances are

2. Please remove the foreign substances

in between the sensor and laminating roller

3. if the heater is defective

3. Please ask to a supplier.

4. If the THERMOSTAT is operating,

4. Please cool down the machine and reoperate the machine.

If same problem arises again,

If the compressor operation is not smooth

1. Please check the pressure gauge of the compressor and machine

if the machine is not switched on.

1. Please check the switch first

2. If the fuse is disconnected.

2. Please replace the fuse with 250V/8A fuse

which was delivered together with machine.

3. PCB BOX is opened

3. Please close the PCB BOX.

Others

38/51

«
...
36
37
38
39
40
...
»

Summary of Contents for PROTOPIC-540 QUATRO SLIT




















































Reviews:

No comments

Related manuals for PROTOPIC-540 QUATRO SLIT

Brand: Olympia Pages: 75

Brand: ibico Pages: 5

Brand: monolith Pages: 10

Brand: monolith Pages: 36

Brand: GBC Pages: 7

Brand: DeWalt Pages: 16

Brand: DataCard Pages: 85

FOTON 30 Automated Laminator

Brand: GBC Pages: 2

wicllaminator L300

Brand: Widinovations Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands