D5038
- I.S. SIL3 Line-Fault Transp. Switch/Prox. Repeater
G.M. International ISM0427-1
2
General Description:
The Switch/Proximity Detector Repeater D5038 is a module suitable for applications requiring SIL 3 level in safety related systems for high risk industries. The unit can be configured
for switches or proximity detectors, located in Hazardous Area, and repeats the input state to the output in Safe Area. The output port can assume two different impedance values (RL
or RH) or it can open completely. The module output repeats the input state according to the following correspondence: low input state -> RL, high input state -> RH. Alternatively, the
output can be configured to invert the input state. In both cases, the output opens if any fault (open or short circuit) occurs at the corresponding input.
Functional Safety Management Certification:
G.M. International is certified by TUV to conform to IEC61508:2010
part 1 clauses 5-6 for safety related systems up to and included SIL3.
Technical Data
Characteristics
Supply:
24 Vdc nom (18 to 30 Vdc), reverse polarity protected.
Current consumption:
30 mA (D5038D), 25 mA (D5038X), 15 mA (D5038S), @ 24 Vdc, typical.
Power dissipation:
1.0 W (D5038D), 1.0 W (D5038X), 0.4 W (D5038S), @ 24 Vdc, typical.
Isolation (test voltage):
I.S. In/Out 1.5 kV; I.S. In/Supply 1.5 kV; I.S. In/ I.S In 500 V; Out/Supply 500 V; Out/Out 500 V.
Input:
Input switching current levels:
ON
≥
2.1 mA, OFF
≤
1.2 mA.
Open fault:
current
≤
0.05 mA.
Short fault:
resistance
≤
100
Ω
.
No fault:
current
≥
0.35 mA and resistance
≥
360
Ω
.
Input equivalent source:
8 V 1 k
Ω
typical (8 V no load, 8 mA short).
Output:
Voltage free SPST solid-state relays, with series (RL) and parallel (RH-RL) resistances, ±5% tolerance.
Fault impedance:
> 1 M
Ω
.
Max voltage:
30 Vdc.
Max current:
15 mA.
Response time:
500
μ
s.
Frequency response:
1 kHz maximum.
Compatibility:
CE mark compliant, conforms to Directives:
2014/34/EU ATEX, 2014/30/EU EMC, 2014/35/EU LVD, 2011/65/EU RoHS.
Environmental conditions:
Operating:
temperature limits – 40 to + 70 °C, relative humidity 95 %, up to 55 °C.
Max altitude:
2000 m a.s.l.
Storage:
temperature limits – 45 to + 80 °C.
Safety description:
ATEX:
II 3(1)G Ex ec [ia Ga] IIC T4 Gc; II (1)D [Ex ia Da] IIIC; I (M1) [Ex ia Ma] I
IECEx:
Ex ec [ia Ga] IIC T4 Gc; [Ex ia Da] IIIC; [Ex ia Ma] I
UL:
NI / I / 2 / ABCD / T4, AIS / I, II, III / 1 / ABCDEFG, AEx nA [ia Ga] IIC T4 Gc;
C-UL:
NI / I / 2 / ABCD / T4, AIS / I, II, III / 1 / ABCDEFG, Ex nA [ia Ga] IIC T4 Gc X
associated apparatus and non-sparking electrical equipment.
Uo/Voc = 10.5 V, Io/Isc = 22 mA, Po/Po = 56 mW at terminals 7-8, 9-10
Um = 250 Vrms or Vdc, -40 °C
≤
Ta
≤
70 °C.
Approvals:
DEMKO 19 ATEX 2290X conforms to EN60079-0, EN60079-11, EN60079-7.
IECEx ULD 19.0029X conforms to IEC60079-0, IEC60079-11, IEC60079-7.
UL & C-UL E222308 conforms to UL 61010-1, UL913, UL 60079-0, UL60079-11, UL60079-15, UL121201 for UL
and CAN/CSA C22.2 No. 61010-1-12, CSA-E60079-0, CSA-E60079-11, CSA-E60079-15 and CSA-C22.2 No. 213 for C-UL.
TUV Certificate No. C-IS-272994-01 SIL 3 conforms to IEC61508:2010 Ed. 2.
TÜV Certificate No. C-IS-236198-09, SIL 3 Functional Safety Certificate conforms to IEC61508:2010 Ed.2, for Management of Functional Safety.
Mounting:
EN/IEC60715 TH 35 DIN-Rail, with or without Power Bus or on customized Termination Board.
Weight:
about 135 g (D5038D and D5038X), 120 g (D5038S).
Connection:
by polarized plug-in disconnect screw terminal blocks to accommodate terminations up to 2.5 mm² (13 AWG).
Location:
installation in Safe Area/Non Hazardous Locations or Zone 2, Group IIC T4 or Class I, Division 2, Group A,B,C,D, T4 or Class I, Zone 2, Group IIC, T4.
Protection class:
IP 20.
Dimensions:
Width 12.5 mm, Depth 123 mm, Height 120 mm.
FSM
SIL 3
Ordering Information
Model:
D5038
1 channel
S
2 channels
D
Power Bus and DIN-Rail accessories:
Bus connector JDFT049
Bus mounting kit OPT5096
duplicator
X
RL = 2.2k
Ω
, RH = 14.3k
Ω
A
RL = 476
Ω
, RH = 1.38k
Ω
B
