background image

Description of symbols

The rating plate on your tool may show symbols. These
represent important information about the product or
instructions on its use.

Wear hearing protection. 
Wear eye protection. 
Wear breathing protection.

Conforms to relevant standards for
electromagnetic compatibility.

Specifications

Nominal voltage:

230–240Vac ~ 50Hz

Input power:

250W

No load speed:

1400 RPM

Table size:

300mm x 300mm

Throat length:

200mm

Bevel angle:

0° to 45°

Cutting capacity:

80mm

Saw blade length:  1400mm
Saw blade width*: 3–12.7mm
Teeth per inch:

6 TPI

* Supplied with a 1400 x 0.35 x 6.35mm general purpose blade

Safety rules for laser lights

The laser light/laser radiation used in the GMC REDEYE®
system is Class 1 with maximum 0.39mW and 650nm
wavelengths. These lasers do not normally present an
optical hazard, although staring at the beam may cause
flash blindness.

Warning. 

Do not stare directly at the laser beam. A

hazard may exist if you deliberately stare into the beam,
please observe all safety rules as follows;

• 

The laser shall be used and maintained in accordance
with the manufacturer’s instructions.

3

Dear Customer

If you require any help with your product, whether it 
is a Warranty claim, spare part or user information, 
please phone our Help Line for an immediate response. 
Phone 1300 880 001 in Australia or 0800 445 721 in 
New Zealand.

Introduction

Your new GMC power tool will more than satisfy your 
expectations. It has been manufactured under stringent 
GMC Quality Standards to meet superior performance 
criteria.
You will find your new tool easy and safe to operate, 
and, with proper care, it will give you many years of 
dependable service.

Caution.

 Carefully read through this entire Instruction 

Manual before using your new GMC Power Tool. Take 
special care to heed the Cautions and Warnings.
Your GMC power tool has many features that will make 
your job faster and easier. Safety, performance, and 
dependability have been given top priority in the 
development of this tool, making it easy to maintain 
and operate.

Environmental protection

Recycle unwanted materials instead of 
disposing of them as waste. All tools, hoses 
and packaging should be sorted, taken to 
the local recycling centre and disposed of 
in an environmentally safe way.

Summary of Contents for LS8B

















Reviews: