background image

Contents

Warranty

2

Introduction

3

Description of symbols

3

Specifications

3

Safety rules for laser lights

3

Safety instructions

4

Additional safety rules for band saws

5

Unpacking

6

Accessories

6

Know your product

7

Assembly

8

Upper blade guide adjustment

8

Lower blade guide adjustment

9

Housing doors 

10

Adjusting the rip fence

10

Adjusting the bevel angle

11

Adjusting the saw blade tension

11

Adjusting the blade tracking

11

Setting the table square with the blade

12

Dust collector connection

12

Turning on and off

12

Installing and removing band saw blades

12

Operation

13

Using the REDEYE® system

13

Changing the batteries

14

Maintenance

14

General inspection

14

Repairs

14

Full 2 Years Home Use Warranty

Whilst every effort is made to ensure your complete 
satisfaction with this tool, occasionally, due to the mass 
manufacturing techniques, a tool may not live up to our 
required level of performance and you may need the 
assistance of our service department.
This product is warranted for a 2-year period for home 
domestic use from the date of the original purchase. If 
found to be defective in materials or workmanship, the 
tool or the offending faulty component will be replaced 
free of charge with another of the same item. A small 
freight charge may apply.
The warranty replacement unit is only made available by 
returning the tool to the place of purchase with a 
confirmed register receipt. Proof of purchase is essential. 
We reserve the right to reject any claim where the 
purchase cannot be verified.
This warranty does not include damage or defects to the 
tool caused by or resulting from abuse, accidents, 
alterations or commercial or business use. 
It also does not cover any bonus accessories unless the 
tool is a GMC Platinum Professional model.
Please ensure that you store your receipt in a safe place.
Conditions apply to the above warranty.
If you need direction of what constitutes a free of 
charge warranty claim, please review the guide given on 
the rear of the Receipt Holder. An indication is given as 
to the types of claim that are permissible, and those 
that are not.

Summary of Contents for LS8B

















Reviews: