![background image](http://html.mh-extra.com/html/gmc/gid18/gid18_manual_2235730011.webp)
GB
11
Switching on/off
WARNING: ALWAYS wear adequate personal protection equipment when
setting up and operating this machine.
1. To start the drill, squeeze the Trigger Switch (6)
2. The built-in Work Light LEDs (3) will illuminate when the Trigger Switch is
squeezed
Note: If the Trigger Switch cannot be pressed down, check that the Forward/
Reverse Switch (5) is not set to its middle position, which locks the device (see
‘Direction control’).
3. The speed of the Impact Driver is controlled by the movement of the trigger:
the further the Trigger Switch is pressed down, the faster the Impact Driver
will run
4. Release the Trigger Switch to stop the machine
WARNING: If the power tool gets excessively hot in use, stop using the tool
immediately and allow to cool before continuing work. The cooling period can be
reduced by operating the Impact Driver at maximum speed with no load. Always
make sure the Motor Vents (4) are not blocked and do not allow dust to enter
the body of the tool through the Motor Vents; dust, especially metallic dust, may
damage or destroy the tool.
Accessories
• A full range of accessories including various types of screwdriver bits
is available from your GMC stockist. Spare parts can be obtained from
toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the mains power supply, before carrying
out any maintenance/cleaning of the charger. Remove the battery before
carrying out any maintenance/cleaning of the Impact Driver.
Note: Both the Impact Driver and the charger contain no user-serviceable
parts. If the device does not perform as outlined in this manual, return it to an
authorised GMC service centre for repair.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised GMC service centre. This
advice also applies to extension cords used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to
wear quickly, and shorten the machine’s service life. Clean the body of
your machine with a soft brush, or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not
use alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray
lubricant
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no
longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic
equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct
way to dispose of power tools
263023_Z1MANPRO1.indd 11
20/06/2014 14:37
Summary of Contents for GID18
