GMC 2001 Sonoma Owner'S Manual Download | Manualshive

Page: 100 / 408

background image

2-28

SECOND (2): Press the clutch pedal as you let up
on the accelerator pedal and shift into SECOND (2).
Then, slowly let up on the clutch pedal as you press
the accelerator pedal.

THIRD, FOURTH AND FIFTH (3, 4 and 5): Shift
into THIRD (3), FOURTH (4) and FIFTH (5) the same
way you do for SECOND (2). Slowly let up on the
clutch pedal as you press the accelerator pedal.

To stop, let up on the accelerator pedal and press
the brake pedal. Just before the vehicle stops,
press the clutch pedal and the brake pedal, and
shift to NEUTRAL.

NEUTRAL: Use this position when you start or idle
your engine.

REVERSE (R): To back up, press the clutch pedal.
After the vehicle stops, shift into REVERSE (R).
For vehicles equipped with the VORTEC 4300 V6
engine, you must wait six seconds before shifting into
REVERSE (R). Slowly let up on the clutch pedal as you
press the accelerator pedal.

NOTICE:

Shift to REVERSE (R) only after your vehicle is
stopped. Shifting to REVERSE (R) while your
vehicle is moving could damage your transmission.

Use REVERSE (R), along with the parking brake, for
parking your vehicle.

Shift Light

If you have a manual
transmission, you have
a SHIFT light.

This light will show you when to shift to the next higher
gear for best fuel economy.

«
...
98
99
100
101
102
...
»

Summary of Contents for 2001 Sonoma

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2001 Sonoma

Brand: Davis Instruments Pages: 16

Brand: Alpine Pages: 8

Brand: Sirius Satellite Radio Pages: 8

Porsche 911 GT3 R

Brand: iRacing Pages: 25

Brand: AddSecure Pages: 14

Brand: Subaru Pages: 16

Brand: Vauxhall Pages: 259

Brand: E&G Classics Pages: 2

Brand: Gator Pages: 8

Brand: benbat Pages: 14

Brand: SPL Pages: 5

Parktronic system Volkswagen Golf MK7

Brand: Car-Systems Pages: 10

Brand: Weltmann KFZ-Teile Pages: 12

Brand: Calix group Pages: 4

2003 Silhouette

Brand: Oldsmobile Pages: 466

Brand: Honda Pages: 22

Brand: Mercedes-Benz Pages: 494

2007 SLR Mclaren

Brand: Mercedes-Benz Pages: 425

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands