GlucoCheck EVOLVE. Owner'S Manual Download Page 27

Page: 27 / 36

Error Messages

MESSAGE

WHAT IT MEANS

ACTION

Appears when the

batteries cannot

provide enough

power for a test.

Replace the batteries

immediately.

Appears when a

used test strip is

inserted.

Repeat with a new test strip.

Appears when

ambient

temperature is

below system

operation range.

System operation range is

10°C to 40°C. Repeat the test

when the meter and test strip

are at the desired temperature.

Appears when

ambient

temperature is

above system
operation range

Problem with the

meter.

Repeat the test with a new

test strip. If the problem

persists, please contact the

local customer service for

assistance.

Appears when test

strip is removed

while counting

down.

Review the instructions and

repeat test with a new test strip.

If the problem persists, please

contact the local customer

service for assistance.

Problem with the

meter.

Please contact the local

customer service for

assistance.

Summary of Contents for EVOLVE.





































Search results

Summary of Contents for EVOLVE.

Reviews:

Related manuals for EVOLVE.

Brands by name

Popular brands

GlucoCheck EVOLVE., Owner'S Manual

Search results

Summary of Contents for EVOLVE.

Reviews:

Related manuals for EVOLVE.

Brands by name

Popular brands