This manual contains a number of precautions to follow in order to help promote safe
use of this equipment.
Warnings related to possible damage to the equipment are indicated by:
Warnings affecting your personal safety are indicated by:
To ensure proper and safe operation, the general safety tips below must be followed.
•
DO NOT
disassemble the scale.
•
ONLY
trained and qualified service personnel should attempt repairs.
•
DO NOT
drop or apply a strong shock to the scale.
•
DO NOT
leave any items on the weighing platter. This can damage the scale.
•
DO NOT
put the scale in a dishwasher.
•
NEVER
immerse the scale in water without weighing platter installed.
1. Place the scale on a stable flat surface.
2. Get power to the unit by one of two ways:
a. Installing Batteries – Remove six screws from battery cover on the bottom of the
scale.
aa. Install three AA-batteries.
NOTE:
Batteries are not included with the scale.
ab. Install battery cover and six screws to secure batteries in scale.
b. Open the AC Adapter power plug cover located on the rear of the scale.
Connect the AC Adaptor to the receptacle and plug into an electrical outlet.
3. Place stainless steel weighing platter over top portion of scale.
1. Make sure nothing is on or touching weighing platter.
2. Turn the unit on by pressing the On/Off key. Scale display will initially show all 8’s
and after three seconds display will show 0’s.
NOTE:
A “Lo” warning will appear on display when battery power is insufficient.
3. Scale weighs in: pounds (lb), ounces (oz), pounds (lb) & ounces (oz), kilograms (kg),
and grams (g) mode. Press the Units key to switch between weighing modes. An
arrow will illuminate on the display screen next to the unit of measure selected.
4. Scale can weigh in Gross or Net modes.
a. If Net weighing is needed, place empty container (or tare weight) on the
weighing platter and press the Tare/Zero key.
Safety Tips
Installation
Operating Instructions
b. The display will show zeros and an arrow will illuminate on the left of the
display next to Tare.
c. When the empty container is removed from weighing platter, the tare weight is
shown as a negative amount and is indicated by an arrow on the display next to
tare.
NOTE:
When no tare weight is used, you are in the Gross weighing mode and there
will be no arrow next to tare
.
5. Place the product (including container if tare weight is being used) on the stainless
steel weighing platter. The total weight is displayed.
NOTE:
If the weight of the object is over the maximum capacity, the display will
show “----”. Remove the object from the patter and reduce the weight of the
object.
6. Remove the first product and continue weighing the next item. If the tare weight
needs to be changed for a new product, then press the Tare/Zero key again to set it
to zero and repeat the steps above for Net weighing.
7. Press the On/Off key to turn the scale off.
NOTE:
The scale will automatically shut-off after 5 minutes of no activity whether it
is operating on battery or AC power.
•
NEVER
place scale in sink without weighing platter installed.
•
DO NOT
hose down or pressure wash any part of the scale.
•
Excess moisture will damage scale and void warranty.
1. If the scale is running on AC power, unplug the scale.
2. Close the AC Adapter power plug cover.
NOTE:
When platter is installed, scale is fully subersible for easy clean-up. Rated
IP67, the scale is protected from dust and water proof up to 1 meter for
30 minutes.
3. Make sure weighing platter is installed on the scale.
4. Place scale in sink with a warm water solution.
5. Use a clean cloth and a mild detergent to wipe down the entire scale.
6. Remove scale from sink.
7. Remove weighing platter. Use a clean, damp cloth and a mild detergent to wipe
down scale housing.
8. Install weighing platter. Use a mild, non-bleach, non-chlorine sanitizer.
Dilute sanitizer per supplier’s instruction!
Cleaning
Operating Instructions
