background image

WA

TER MO

W

ATER ENHANCEMENT

15

ZeroSpot Portable Deionized Water System

I. Required accessories (not included in the package)

User Guide

Garden hose (x2) + sprayer (x1) (See Fig. 1 and 2)

Fig. 1

 - Garden hose

Fig. 2

 - Sprayer

1.  Ensure incoming water is shut off.

2.  Use garden hose to connect system to water supply through connection marked “IN”. Connect garden 

hose and sprayer system connection marked “OUT”. To prevent leaks, ensure garden hose gaskets are 

in place before connecting to the adapter. 

3.  Connect the sprayer to garden hose. (NOTE: Ensure flowrate does not exceed 2.5 GPM / 9.5 LPM. It is 

recommended to use sprayer’s flat or center setting to restrict flowrate.)

4.  Open incoming water supply and flush system with sprayer open for 5 minutes to ensure cartridges are 

completed soaked and primed. 

5.  After flushing for 5 minutes, the system is ready to use.

NOTE:

 Flushing the system is only required for first use after new cartridges are installed. 

II. Cartridge Replacement Instruction

A. Tools

B. Item Checklist

20” Housing wrench

ZeroSpot

 Cart

Summary of Contents for ZeroSpot ZS40B





















Reviews: