background image

  

                                                 

 

 

 

                  

 

 

Safety 

The following safety instructions apply to all game operators and service personnel.  Specific warnings 
and cautions will be found throughout this manual.   

Please read this page before preparing your arcade cabinet for game play. 

Use the following safety guidelines to help protect the system from potential damage and to ensure your 
personal safety. 

• 

To help avoid damage to the computer, the power supply on the computer automatically detects the 
voltage to match the AC power available at the location: 

• 

115 volts / 60Hz in most of North and South America and some Far Eastern countries such as Japan, 
South Korea and Taiwan  

• 

230 volts  / 50Hz in most of Europe, the Middle East and the Far East 

• 

To help prevent electric shock, plug the system into a properly grounded power source.  These 
cables are equipped with 3-prong plugs to help ensure proper grounding.  Do not use adapter plugs 
or remove the grounding prong from a cable.  If you must use an extension cable, use a 3 wire cable 
with properly grounded plugs. 

• 

To help protect your system from sudden increases and decreases in electrical power, use a surge 
suppressor, line conditioner or Uninterruptible Power Supply (UPS). 

• 

Be sure nothing rests on the system's cables and that the cables are not located where they can be 
stepped on or tripped over. 

• 

Do not spill food or liquid on the cabinet.   

• 

Do not push any objects into the openings of the system.  Doing so can cause fire or electric shock by 
shorting out interior components. 

• 

Keep your computer far away from radiator and other heat sources.   

• 

Do not block cooling vents.   

Warnings 

 

 

To avoid electrical shock, unplug the cabinet before performing the 
installation procedures. 

 

 

Global VR assumes no liability for any damages or injuries incurred 
while setting up the EA Sports™ PGA Tour® Golf cabinet.  Only 
qualified service personnel should perform this installation! 

 

 
 

 

Six Gun Select Joshua OS Upgrade 

2

 

 

040-1102-01 Rev C 4/27/2004 

Summary of Contents for Six Gun Select









Reviews: