Global Fire Equipment CHAMELEON GEKKO Installation & Commissioning Manual Download Page 26

Page: 26 / 29

Global Fire Equipment //

globalfire.pt

ma_chmcomm_01_010001_en_191121

“PANEL CONFIGURATION MISMATCH”

One Panel in ACTIVE MODE and all other in INSTALLATION MODE

Panel 1

, due to a failure on the network, has changed to Installation mode and the others have not. All panels will trigger

“Panel Configuration Mismatch” on Panel 1. Panel 1 will trigger the fault mentioning all other panels on the queue.

Panel 1

Panel 2

Panel 3

PANEL 02

PANEL CONFIGURATION MISMATCH

TOTAL NUMBER OF FAULTS 0002

PANEL 01

PANEL CONFIGURATION MISMATCH

TOTAL NUMBER OF FAULTS 0001

PANEL 01

PANEL CONFIGURATION MISMATCH

TOTAL NUMBER OF FAULTS 0001

PANEL 03

PANEL CONFIGURATION MISMATCH

TOTAL NUMBER OF FAULTS 0002

Summary of Contents for CHAMELEON GEKKO






























Search results

Summary of Contents for CHAMELEON GEKKO

Reviews:

Related manuals for CHAMELEON GEKKO

Brands by name

Popular brands

Global Fire Equipment CHAMELEON GEKKO, Installation & Commissioning Manual

Search results

Summary of Contents for CHAMELEON GEKKO

Reviews:

Related manuals for CHAMELEON GEKKO

Brands by name

Popular brands