Global Fire Equipment CHAMELEON GEKKO Installation & Commissioning Manual Download Page 2

Page: 2 / 29

Global Fire Equipment //

globalfire.pt

ma_chmcomm_01_010001_en_191121

Complete list of functions

Specific Network Related Functions

STEP BY STEP NETWORK COMMISSIONING

Open network LOOP

Power Up in Installation Mode

Panel Lamp Check

Check Panel Address

Check Panel Version

Check All Communication Channels (CHx)

Check Known Panels

Debug Network messages

Restart Network Panels

Close network LOOP

Upload and Broadcast Configuration to the network

Clear NVRAM

Wait 2 minutes for network recognition

Change system to Active Mode

Verify remote devices on the installation

TROUBLESHOOTING

“COMMUNICATION FAILURE”

RX connection break on Panel 2 (disconnect RX1 or RX2)

TX1 connection break on Panel 2

TX2 connection break on Panel 2

“PANEL CONFIGURATION MISMATCH”

One Panel in ACTIVE MODE and all other in INSTALLATION MODE

Upload a configuration without broadcast

Selective Disablements different between panels

8-5-2 Known Panels - Debug on communications

Commissioning phase with “open loop” topology, with Panels on Installation Mode.

Commissioning phase with “closed loop” topology, with Panels on Installation Mode.

Summary of Contents for CHAMELEON GEKKO






























Search results

Summary of Contents for CHAMELEON GEKKO

Reviews:

Related manuals for CHAMELEON GEKKO

Brands by name

Popular brands

Global Fire Equipment CHAMELEON GEKKO, Installation & Commissioning Manual

Search results

Summary of Contents for CHAMELEON GEKKO

Reviews:

Related manuals for CHAMELEON GEKKO

Brands by name

Popular brands