manualshive.com logo in svg

gledhill Stainless Lite Direct 90-300 litres, Design, Installation & Servicing Instructions, Page: 31 / 32

Share
Download
gledhill Stainless Lite Direct 90-300 litres Design, Installation & Servicing Instructions Download Page 31

Page 31

TERMS AND C

ONDITIONS

of three years from the date of delivery Gledhill will replace, free of charge, any plate heat exchanger fitted in 
the appliance as original equipment in which scale formation occurs that materially reduces the effectiveness 
of the plate heat exchanger.  This guarantee does not extend to any other component installed within the 
Gledhill appliance or elsewhere in the Purchasers domestic water system.

9.4.
9.4.1. In respect of goods supplied by us  and in respect of any installation work carried out by or on our behalf, our 

entire liability and the purchaser’s sole remedies (subject to the Guarantees) shall be as follows:-
(a) We accept liability for death or personal injury to the extent that it results from our negligence or that of 

our employees

(b) Subject to the other provisions of this clause 9 we accept liability for direct physical damage to tangible 

property to the extent that such damage is caused by our negligence or that of our employees, agents or 
subcontractors.

(c) Our total liability to the purchaser over and above any liability to replace under the Guarantees (whether 

in contract or in tort including negligence) in respect of any one cause of loss or damage claimed to result 
from any breach of our obligations hereunder, shall be limited to actual money damages which shall not 
exceed £20,000 provided that such monetary limit shall not apply to any liability on the part of ourselves 
referred to in paragraph (a) above

(d) Except as provided in paragraph (a) above but otherwise not withstanding any provision herein contained 

in no event shall we be liable for the following loss or damage howsoever caused and even if foreseeable 
by us or in our contemplation:-

   

(i) economic loss which shall include loss of profits, business revenue, goodwill or anticipated savings 

   

(ii) damages in respect of special indirect or consequential loss or damage (other than death, personal 

injury and damage to tangible property)

   

(iii) any claim made against the purchaser by any other party (save as expressly provided in paragraph (b) 

above)

(e) Except in respect of our liability referred to in paragraph (a) above no claim may be made or action 

brought (whether in contract or in tort including negligence) by the purchaser in respect of any goods 
supplied by us more than one year after the date of the invoice for the relevant goods.

(f) Without prejudice to any other term we shall not be liable for any water damage caused directly or 

indirectly as a result of any leak or other defect in the goods.    We cannot control the conditions of use of 
the goods or the time or manner or location in which they will be installed and the purchaser agrees to 
be fully responsible for testing and checking all works which include the goods at all relevant times (up 
to, including and after commissioning) and for taking all necessary steps to identify any leaks and prevent 
any damage being caused thereby.

(g) Nothing in these Conditions shall confer on the purchaser any rights or remedies to which the purchaser 

would not otherwise be legally entitled

10.

LOSS OR INJURY 

Notwithstanding any other provision contained herein the purchaser’s hereby agree to fully indemnify us against 
any damages losses costs claims or expenses incurred by us in respect of any claim brought against us by any third 
party for:-
(a)

any loss injury or damage wholly or partly caused by any goods supplied by us or their use.

(b)

any loss injury or damage wholly or partly caused by the defective installation or substandard workmanship 
or materials used in the installation of any goods supplied by us.

(c)

any loss injury or damage in any way connected with the performance of this contract.

(d)

any loss resulting from any failure by the purchaser to comply with its obligations under these terms as to 
install and/or check  works correctly.

PROVIDED

 that this paragraph will not require the purchaser to indemnify us against any liability for our own acts 

of negligence or those of our employees agents or sub-contractors

FURTHER

 in the case of goods supplied by us which are re-sold and installed by a third party by the purchaser it will 

be the sole responsibility of the purchaser to test the goods immediately after their installation to ensure that inter 
alia they are correctly installed and in proper working order free from leaks and are not likely to cause any loss injury 
or damage to any person or property.

11.

VARIATION OF WARRANTY AND EXCLUSION

Should our warranty and exclusion be unacceptable we are prepared to negotiate for variation in their terms but 
only on the basis of an increase in the price to allow for any additional liability or risk which may result from the 
variation.
Purchasers are advised to insure against any risk or liability which they may incur and which is not covered by our 
warranty.

12.

RISK AND RETENTION OF TITLE

(a)

goods supplied by us shall be at the Purchaser’s risk immediately upon delivery to the Purchaser or into 
custody on the Purchaser’s behalf or to the Purchaser’s Order.  The Purchaser shall effect adequate insurance 
of the goods against all risks to the full invoice value of the goods, such insurance to be effective from the time 
of delivery until property in the goods shall pass to the Purchaser as hereinafter provided.

(b)

property in the goods supplied hereunder will pass to the Purchaser when full payment has been made by the 
Purchaser to us for :-
(i) the goods of the subject of this contract.
(ii) all other goods the subject to of any other contract between the Purchaser and us which, at the time of 

payment of the full price of the goods sold under this contract, have been delivered to the Purchaser but 
not paid for in full.

(c)

until property in the goods supplied hereunder passes to the Purchaser in accordance with paragraph (2) 
above.
(i) the Purchaser shall hold the goods in a fiduciary capacity for us and shall store the same separately from 

any other goods in the Purchaser’s possession and in a manner which enables them to be identified as our 
goods.

(ii) the Purchaser shall immediately return the goods to us should our authorised representative so request.  

All the necessary incidents associated with a fiduciary relationship shall apply.

(d)

the Purchaser’s right to possess the goods shall cease forthwith upon the happening of any of the following 
events, namely :-
(i) if the Purchaser fails to make payment in full for the goods within the time stipulated in clause 4 hereof.
(ii) if the Purchaser, not being a company, commits any act of bankruptcy, makes a proposal to his or her 

creditors for a compromise or does anything which would entitle a petition for a Bankruptcy Order to be 
presented.

(iii) if the Purchaser, being a company, does anything or fails to do anything which would entitle an 

administrator or an administrative receiver or a receiver to take possession of any assets or which would 
entitle any person to present a petition for winding up or to apply for an administration order.

(e)

the Purchaser hereby grants to us an irrevocable licence to enter at any time any vehicle or premises owned 
or occupied by the Purchaser or in the possession of the Purchaser for the purposes of repossessing and 

recovering any such goods the property in which 
has remained in us under paragraph (2) above.  We 
shall not be responsible for and the Purchaser  will 
indemnify us against liability in respect of damage 
caused to any vehicle or premises in such repossession 
and removal being damaged which it was not 
reasonably practicable to avoid.

(f)

notwithstanding paragraph (3) hereof and subject to 
paragraph (7) hereof, the Purchaser shall be permitted 
to sell the goods to third parties in the normal course 
of business.  In this respect the Purchaser shall act 
in the capacity of our commission agent and the 
proceeds of such sale :-
(i) shall be held in trust for us in a manner which 

enables such proceeds to be identified as such, 
and :

(ii) shall not be mixed with other monies nor paid into 

an overdrawn bank account.

We, as principal, shall remunerate the Purchaser as 
commission agent a commission depending upon 
the surplus which the Purchaser can obtain over and 
above the sum, stipulated in this contract of supply 
which will satisfy us.

(g)

in the event that the Purchaser shall sell any of the 
goods pursuant to clause (6) hereof, the Purchaser 
shall forthwith inform us in writing of such sale and 
of the identity and address of the third party to whom 
the goods have been sold.

(h)

if, before property in the goods passes to the 
Purchaser under paragraph (2) above the goods are or 
become affixed to any land or building owned by the 
Purchaser it is hereby agreed and declared that such 
affixation shall not have the effect of passing property 
in the goods to the Purchaser.  Furthermore if, before 
property in the goods shall pass to the Purchaser 
under paragraph (2) hereof, the goods are or become 
affixed to any land or building (whether or not owned 
by the Purchaser), the Purchaser  shall:-
(i) ensure that the goods are capable of being removed 

without material injury to such land or building.

(ii) take all necessary steps to prevent title to the 

goods from passing to the landlord of such land 
or building.

(iii) forthwith inform us in writing of such affixation 

and of the address of the land or building 
concerned.

The Purchaser warrants to repair and make good 
any damage caused by the affixation of the goods 
to or their removal from any land or building and 
to indemnify us against all loss damage or liability 
we may incur or sustain as a result of affixation or 
removal.
(i) in the event that, before property in the goods 

has passed to the Purchaser under paragraph (2) 
hereof, the goods or any of them are lost, stolen, 
damaged or  destroyed :-

(ii) the Purchaser shall forthwith inform us in writing 

of the fact and circumstances of such loss, theft, 
damage or destruction.

(iii) the Purchaser shall assign to us the benefit of any 

insurance claim in respect of the goods so lost, 
stolen, damaged or destroyed.

13.

NON-PAYMENT

If the Purchaser shall fail to make full payment for the goods 
supplied hereunder within the time stipulated in clause 4 
hereof or be in default of payment for any other reason then, 
without prejudice to any of our other rights hereunder, we 
shall be entitled to stop all deliveries of goods and materials 
to the Purchaser, including deliveries or further deliveries of 
goods under this contract.  In addition we shall be entitled 
to terminate all outstanding orders.

14.

VALUE ADDED TAX

All prices quoted are exclusive of Value Added Tax which 
will be charged at the rate ruling at the date of despatch of 
invoice.

15.

TRADE SALES ONLY

We are only prepared to deal with those who are not 
consumers within the terms of the Unfair Contract Terms 
Act 1977, the Sale of Goods Act 1979 and the Supply of 
Goods and Services Act 1982.  Accordingly any person who 
purchases from us shall be deemed to have represented that 
he is not a consumer by so purchasing.

16.

JURISDICTION

The agreement is subject to English law for products 
delivered in England and Scottish law for products delivered 
in Scotland and any dispute hereunder shall be settled in 
accordance therewith dependent upon the location.

Summary of Contents for Stainless Lite Direct 90-300 litres

































Reviews:

No comments