background image

Page 13

INSTALLATION

C

ONTR

OLS

BoilerMate Heating/Hot Water Controls

The current BoilerMate A-Class SP Sol incorporates separate heating/hot water and 
solar control systems. 

The BoilerMate A-Class SP Sol heating and hot water controls operate in the same way 
as the basic BoilerMate appliances but the single channel clock and the two rocker 
switches have been replaced by a two channel digital clock. (Channel 1 controls the 
gas boiler /hot water and Channel 2 the heating.) Details of how to set the clock are 
shown in the user instructions which are provided in the plastic wallet fixed at the 
bottom of the front panel. Recommendations regarding the setting of Channel 1 are 
provided on the label adjacent to the front panel controls (see below). Channel 2 
should be set as normal to control the heating on/off times required.

Label 1

 - Channel 1 of this digital clock is dedicated to heating of the hot water.  This 

can be set to hold off the boiler during periods of potential high solar gain periods 
eg 10.00 am to 16.00 pm allowing maximum solar contribution to the thermal store. 
Central heating channel 2 will not be affected by holding off the boiler and operates 
independently of channel 1.

If a high hot water demand is expected or the appliance runs out of hot water due to 
poor solar gains, the setting of Channel 1 can be overridden which will bring on the 
boiler and ensure hot water is made available. Dependant on use/weather, the ‘off’ 
times suggested above can be adjusted as necessary to ensure adequate amounts 
of hot water are available.

The Switch 6kW electrical emergency back up system is fitted to this appliance.  This 
is switched on by moving the ‘mode’ rocker switch from normal to switch and is used 
in the event of boiler failure.  It is unlikely to be needed in Summer but can be used 
in Winter as required to provide some heating and hot water in conjunction with the 
solar input until the problem can be resolved.  

It is an emergency only system and must not be used if the main system is 
working correctly. 

BoilerMate

A-CLASS SP Solar

OFF:
SLOW FLASHING
MEDIUM FLASHING
RAPID FLASHING
ON:

Normal
Switch failure
Switch backup selected
Overheat safety trip
Switch on

PUSH BUTTON

To reset appliance

Normal

Control circuit power
supply

Red LED

Black button

Green rocker switch

(illuminated when on)

Figure 1.11

Label 1

See above for wording

Mode

Switch

0

1

2

3

4

5

6

7

14

16

18

20

22

24

+

-

Menu OK

Res.

+1h

Summary of Contents for BMA 200 SP-SOL

























Reviews: