background image

Page 10

System Controls

The system controls should be developed in conjunction with the heat 
pump manufacturer.

Using the buffer store in conjunction with an additional heat source 
requires a more sophisticated control system. This is to stop the boiler 
dominating the heating of the cylinder and reducing the possible input 
of the heat pump.

Soldering 

In line with good plumbing practice, use with excessive flux should 
be avoided. 

When soldering above the cylinder, ensure flux/solder does not 
contaminate the cylinder below, since this can cause corrosion. 

Flushing the system 

Before completing the heat pump connections, the heating installation 
must be flushed in order to remove any impurities that may be present, 
residues of sealing agents. Any accumulation of residues and other 
deposits in the heat pump condenser may result in reduced efficiency of 
the unit or a total failure of the heat pump.

Water Treatment And Frost Protection

Although the Buffer store has no special water treatment requirements, 
the radiators and other parts of the circuit will require the application of a 
scale and corrosion inhibitor. The heat pump and the external connecting 
pipe work will also require protection against freezing. For this reason, a 
combined antifreeze and inhibitor product such as Fernox Alphi 11 must 
be used (see Fernox Alphi 11 datasheet in Appendix A).

The volumes and concentration should be calculated in accordance with 
the manufacturer’s instructions and when calculating the system volume 
i.e. the water content, the volume of the Buffer store should be taken into 
account (see technical specification tables).

NOTE

At the time of commissioning, complete all relevant sections of 
the Benchmark Checklist located on the inside back pages of this 
document.

This must be completed during commissioning and left with the 
product to meet the Warranty conditions offered by Gledhill.

INSTALLATION

COMMISSIONING

Summary of Contents for 120IND





















Reviews: