background image

11/21/14 (Rev. 01) 

201-8401912 

 

 
 
 

General Information 

 
This system improves the taste and odor and reduces many chemical 
contaminants  in  drinking  water.    This  system  has  been  tested 
according  to  NSF/ANSI  42  and  53  for  the  reduction  of  the 
substances  listed  on  the  previous  page.    The  concentration  of  the 
indicated substances in water entering the system  was reduced to a 
concentration  less  than  or  equal  to  the  permissible  limit  for  water 
leaving  the  system,  as  specified  in  NSF/ANSI  42  and  53.    The 
testing was performed using spiked tap water at a flow rate of 0.74 
GPM  (2.8  L/min.),  pH  of  7.5 

  0.5,  pressure  of  60  PSIG,  and 

temperature of 68 

 5

F.    

 
 

Installation Requirements 

 
Pressure Range ........................................... 40-100 psig (276-689kPa) 
Temperature Range  ................................................ 40-100

F (4-38

C) 

Service Flow Rate (maximum) ........................... 0.74 GPM (2.8 LPM) 
Service Life ................................................. 350 Gallons (1325 Liters) 

 

The filter element contains activated carbon.  After the new filter is 
installed,  flush  water  through  to  allow  fine,  harmless  carbon 
particles  to  purge  from  the  filter,  until  the  “fines”  in  the  filtered 
water are no longer visible, or approximately 10 minutes. 
 

Installation and Maintenance 

 

All  plumbing  should  be  done  in  accordance  with  local  codes  and 
requirements.  This system should be installed on a cold water supply 
only.    In  Massachusetts,  plumbing  codes  CMR-248  3.00  and  10.00 
shall be adhered to.  Consult with your licensed plumber.  Filter should 
be  replaced  every  350  gallons  or  six  months,  whichever  comes  first.  
For replacement elements, call 1-800-247-1087

 

or contact your nearest 

The Home Depot’s store.  Replacement filter prices will vary.  Current 
pricing for the replacement filters HDGMBF4 is approximately $50 to 
$75. 

 
.   

 

Manufactured and warranted by: 
Ecodyne Water Systems 
1890 Woodlane Drive 
Woodbury, MN 55125 
 
 
 

 

FOR IOWA ONLY 

 

All sales in Iowa require the following signature before consummation of sale.  These signatures must be retained by seller/renter for 2 years minimum. 

 
 
 

Buyer/Renter ______________________ 

Date  

 

 
Seller  

Date  

 

 
Seller’s Address  

 

 
Seller’s Phone #  

 

Product:  GLACIER BAY Drinking Water Filter Model HDGMBS4

 

 

 

Tested and certified by WQA against 
NSF/ANSI standard 42, 53, and USEPA 
microbiological guide for the reduction of 
the claims specified in this document. 

System  tested  and  certified  by  NSF 
International  against  NSF/ASNI  Standard 
42  and  53  for  Chlorine  Taste  and  Odor, 
VOC,  Lead,  Class  I  Particulate  and  for 
Material Requirements. 

Summary of Contents for HDGMBS4














Reviews: