manualshive.com logo in svg

GIRBAU H5020, Instructions Manual, Page: 2 / 17

Share
Download
GIRBAU H5020 Instructions Manual Download Page 2

 
 

Bearings Replacement 

 

Cod. 409748 Bearing 
Rev. 00/0204 

2 

 

 
INDEX

 

 
SAFETY INSTRUCTIONS 
 
1. Preparation 

1.1.  Variants of bearings’ box. 
1.2. Necessary tools 
1.3.  Pieces and materials 
1.4. Parts  
1.5.  Emptying the residual bath 
1.6.  Disassembling the covers 
1.7.  Disassembling the front panel of the 

washing machine 

1.8.  Disassembling the outer drum front 
1.9.  Disassembling the drum 

 

 

2.  Machines without drainage. Action  

2.1.  Disassembling the bearings’ box 
2.2.  Changing the bearings 
2.3.  Preparing the outer drum 
2.4.  Assembling the bearings’ box 

 
 
3.  Machines with drainage. Action 

3.1.  Disassembling the bearings’ box 
3.2.  Changing the bearings 
3.3.  Preparing the back of the outer drum 
3.4.  Assembling the bearings’ box 

 
 
4.  Changing the seals 
 
 
5.  Assembly and verification 

5.1.  Assembling the drum 
5.2.  Assembling the outer drum front 
5.3.  Assembling the front panel of the 

washing machine 

5.4.  Assembling the covers 
5.5. Checking 

the 

machine 

 

 
 

SAFETY INSTRUCTIONS

 

 
 

IMPORTANT 

The operations described in these instructions are 
restricted to the Authorised Service  

 

  WARNING!!

 

Before attempting any service or inspection of the 
washing machine:  
 

•

 

COMPLETELY

 disconnect the machine from 

the power source and check for accidental 
reconnection. In LOGI CONTROL units, moving 
the 

ON

 switch to the OFF position is not 

sufficient. 

•

  Wait at least five minutes after disconnecting 

the machine before beginning this operation. 
Within the electrical circuit of the washer exists 
high powered charges which can produce 
important electrical shocks even after the 
machine has been disconnected. 

•

  Close and mechanically interlock the water 

supply valves and check that machine has 

COMPLETELY 

drained, parts have cooled 

down and that no pieces are in movement 
through inertia. 

 
Failure to comply with this warning may result in 
serious injury.

 

Summary of Contents for H5020


















Reviews:

No comments