Gilbarco Veeder-Root FlexPay IV Encore 700 S Manual Download Page 7

MDE-5287B

 

3

SECTION 2 -  IMPORTANT SAFETY INFORMATION                                 

2

Important Safety Information

Notes: 1) Save this Important Safety Information section in a 

readily accessible location.

 2) Although DEF is non-flammable, Diesel is 

flammable. Therefore, for DEF cabinets that are 
attached to Diesel dispensers, follow all the notes 
in this section that pertain to flammable fuels.

This section introduces the hazards and safety precautions 
associated with installing, inspecting, maintaining or servicing 
this product. Before performing any task on this product, read 
this safety information and the applicable sections in this manual, 
where additional hazards and safety precautions for your task 
will be found. Fire, explosion, electrical shock or pressure 
release could occur and cause death or serious injury, if these 
safe service procedures are not followed. 

Preliminary Precautions

You are working in a potentially dangerous environment of 
flammable fuels, vapors, and high voltage or pressures. Only 
trained or authorized individuals knowledgeable in the related 
procedures should install, inspect, maintain or service this 
equipment

.

Emergency Total Electrical Shut-Off

The first and most important information you must know is how to 
stop all fuel flow to the pump/dispenser and island. Locate the 
switch or circuit breakers that shut off all power to all fueling 
equipment, dispensing devices, and Submerged Turbine Pumps 
(STPs). 

 

The EMERGENCY STOP, ALL STOP, and PUMP 
STOP buttons at the cashier

s station WILL NOT 

shut off electrical power to the 

pump/dispenser. This means that even if you activate 
these stops, fuel may continue to flow uncontrolled. 

You must use the TOTAL ELECTRICAL 

SHUT-OFF in the case of an emergency and not the 
console

s ALL STOP and PUMP STOP or similar 

keys.

!

WARNING

!

Total Electrical Shut-Off Before Access

Any procedure that requires access to electrical components or 
the electronics of the dispenser requires total electrical shut off of 
that unit. Understand the function and location of this switch or 
circuit breaker before inspecting, installing, maintaining, or 
servicing Gilbarco equipment.

Evacuating, Barricading and Shutting Off

Any procedure that requires access to the pump/dispenser or 
STPs requires the following actions:

• An evacuation of all unauthorized persons and vehicles from 

the work area 

• Use of safety tape, cones or barricades at the affected unit(s)
• A total electrical shut-off of the affected unit(s)

Read the Manual

Read, understand and follow this manual and any other labels or 
related materials supplied with this equipment. If you do not 
understand a procedure, call the Gilbarco Technical Assistance 
Center (TAC) at 1-800-743-7501. It is imperative to your safety 
and the safety of others to understand the procedures before 
beginning work.

Follow the Regulations

Applicable information is available in National Fire Protection 
Association (NFPA) 30A; 

Code for Motor Fuel Dispensing 

Facilities and Repair Garages

, NFPA 70; 

National Electrical 

Code (NEC)

, Occupational Safety and Health Administration 

(OSHA) regulations and federal, state, and local codes. All these 
regulations must be followed. Failure to install, inspect, maintain 
or service this equipment in accordance with these codes, 
regulations and standards may lead to legal citations with 
penalties or affect the safe use and operation of the equipment.

Replacement Parts

Use only genuine Gilbarco replacement parts and retrofit kits on 
your pump/dispenser. Using parts other than genuine Gilbarco 
replacement parts could create a safety hazard and violate local 
regulations.

Safety Symbols and Warning Words

This section provides important information about warning 
symbols and boxes.

Alert Symbol 

This safety alert symbol is used in this manual and on 

warning labels to alert you to a precaution which must be 
followed to prevent potential personal safety hazards. Obey 
safety directives that follow this symbol to avoid possible injury or 
death.

Signal Words

These signal words used in this manual and on warning labels 
tell you the seriousness of particular safety hazards. The 
precautions below must be followed to prevent death, injury or 
damage to the equipment:

DANGER

:

 

Alerts you to a hazard or unsafe practice 

which will result in death or serious injury.

WARNING

: Alerts you to a hazard or unsafe practice that 

could result in death or serious injury. 

CAUTION

 with Alert symbol: Designates a hazard or 

unsafe practice which may result in minor injury.

CAUTION

 without Alert symbol: Designates a hazard or 

unsafe practice which may result in property or 
equipment damage.

Working With Fuels and Electrical Energy

Prevent Explosions and Fires

Fuels and their vapors will explode or burn, if ignited. Spilled or 
leaking fuels cause vapors. Even filling customer tanks will cause 
potentially dangerous vapors in the vicinity of the dispenser or 
island.

DEF is non-flammable. Therefore, explosion and fire safety 
warnings do not apply to DEF fluid lines.

!

!

!

Summary of Contents for Veeder-Root FlexPay IV Encore 700 S

























Reviews: