manualshive.com logo in svg

Gigahertz Solutions NFA 1000, Operating Manual, Page: 33 / 40

Share
Download
Gigahertz Solutions NFA 1000 Operating Manual Download Page 33

 

   

 

Made in Germany

 

© Gigahertz Solutions GmbH 

- 31 -

 

 

May 2017

 

9

 

What if… (FAQ) 

Answers to frequently asked questions regarding 
the NFA1000/NFA400  

Make sure to be using the most current firmware version! 

 

 

 

The device does not react 

to switching or pressing a key

 

Unlock SD-card! (Push micro switch on the left  

of the card upwards) 

Restart: All switches up – switch off – switch on. 

RESET: Switch off meter, open battery compart-

ment, disconnect the two battery plugs, reconnect 

the batteries after about one minute and switch the 

meter back on. 

 

Calibraton of capacity display

 after battery change, firm-

ware update, or if the display shows 

„nBAT“, „00:00“, or an 

absurd remaining battery capacity reading. 

 

If applicable, disconnect external power supply from 

the meter. Leave the meter is switched on for a couple 

of minutes, so that it can recalibrate itself, then switch 

off and on again. Now the updated remaining battery 

life in the log mode will be displayed 

For a recalibration, leave the meter running (without the 

AC adapter) until it automatically switches off. Leave to 

rest for at least one hour. Switch the meter back on un-

til it again automatically switches off after a couple of 

minutes. Then charge for at least 14 hours. In some 

cases, the meter needs to be switched off and back on 

after having been in use for a couple of minutes, before 

it displays the current running time.  

 

 

There is no recording 

(status LED does not turn green)

 

Insert or unlock SD-card!  

(Push micro switch on the left of the card upwards) 

Summary of Contents for NFA 1000









































Reviews:

No comments