background image

Made in Germany

 

May 2017 

- 16 - 

© Gigahertz Solutions GmbH

 

5

 

How to Measure  
and Data-Log 

5.1

 

“Live”-Measurement 

Of course the meter can be used the “conventional” way: 
simply switch it on, set the required measurement parame-
ters, and read the values recorded. When operating in the 
conventional mode, the “Status-LED” will be yellow.  

In addition, the device is capable of logging all settings as 
well as the measurement values of all four channels at once 
(i.e. the three field axis values plus one additional channel). 
This data is stored onto an SD-card for future analysis. This 
function can be activated by temporarily switching the 
“Power” switch to “Log.” until the status LED turns yellow. 
Then switch the “Power” switch back to “On”. Please note: 
When logging with the power switch set to ”LOG” and 
changing the field of measurement and recording (for in-
stance from M3D to E3D), this will cause the recording ses-
sion to be closed and a new log file to be created.  

These recordings can be annotated by real-time audio re-
cordings which will be assigned automatically to the respec-
tive measurement for replay. 

 

The following chapters 5.2 and 5.3 are only relevant for 
the NFA 1000. 

5.2

 

Guided 9 Point Measurement  
of Sleeping Areas 

For alternating electric fields, the guide-
lines issued by the VDB e.V., Germany, 
require a detailed analysis of the floating 
potential electrical field in sleeping areas, 
specifying nine points (three each in the 
head-, torso- and foot area, with the out-
er edge of the instrument located 10 cm 
off the bed’s edge). The NFA in combination with NFAsoft 
allows for a “guided measurement” in order to efficiently ac-
complish data collection and evaluation.  

Summary of Contents for NFA 1000









































Reviews: