manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

599 

 

 

The idle frame wake up method is selected by default. When an idle frame is detected on the 
RX pin, the hardware clears the RWU bit and exits the mute mode. When it is woken up by 
an idle frame, the IDLEF bit in USART_STAT will not be set. 

When the WM bit of in USART_CTL0 register is set, the MSB bit of a frame is detected as the 
address flag. If  the address flag is high, the frame is treated as an address frame. If  the 
address flag is low, the frame is treated as a data frame. If  the LSB 4 or 7 bits, which are 
configured by the ADDM bit of the USART_CTL1 register, of an address frame is the same 
as the ADDR bits in the USART_CTL1 register, the hardware will clear the RWU bit and exits 
the mute mode. The  RBNE bit will be set when the frame that wakes up the USART. The 
status bits are available in the USART_STAT register. If the LSB 4/7 bits of an address frame 
defers from the ADDR bits in the USART_CTL1 register, the hardware sets the RWU bit and 
enters mute mode automatically. In this situation, the RBNE bit is not set. 

If the PCEN bit in USART_CTL0 is set, the MSB bit will be checked as the parity bit, and the 
bit preceding the MSB bit is detected as the address bit. If the ADDM bit is set and the receive 
frame is a 7bit data, the LSB 6 bits will be compared with ADDR[5:0]. If the ADDM bit is set 
and the receive frame is a 9bit data, the LSB 8 bits will be compared with ADDR[7:0]. 

18.3.8. 

LIN mode 

The local interconnection network mode is enabled by setting the LMEN bit in USART_CTL1. 
The CKEN, STB[1:0] bit in USART_CTL1 and the SCEN, HDEN, IREN bits in USART_CTL2 
should be cleared in LIN mode. 

When transmitting a normal data frame, the transmission procedure is the same as the normal 

USART mode. The data bits length can only be 8. And the break frame is 13-

bit ’0’, followed 

by 1 stop bit. 

The break detection function is totally independent of the normal USART receiver. So a break 
frame can be detected during the idle state or during a frame. The expected length of a break 
frame can be selected by configuring LBLEN in USART_CTL1. When the RX pin is detected 
at low state for a time that is equal to or longer than the expected break frame length (10 bits 
when LBLEN=0, or 11 bits when LBLEN=1), the LBDF bit in USART_STAT is set. An interrupt 
occurs if the LBDIE bit in USART_CTL1 is set. 

As shown in 

Figure 18-9. Break frame occurs during idle state

, if a break frame occurs 

during the idle state on the RX  pin, the USART receiver will receive an all ‘0’ frame, with an 
asserted FERR status. 

Figure 18-9. Break frame occurs during idle state 

frame0

frame1

frame2

1 frame time

USART_RDATA 

data0

data1

00000000

data2

FERR

RX pin

LBDF

 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

National Instruments NI 9213 Getting Started preview
NI 9213
Brand: National Instruments Pages: 11
ZALMAN RESERATOR 1 Manual preview
RESERATOR 1
Brand: ZALMAN Pages: 22
Z-Com ZCN-1523H-5-16 Quick Installation Manual preview
ZCN-1523H-5-16
Brand: Z-Com Pages: 18
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Brand: ADTRAN Pages: 20
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Brand: Comtrend Corporation Pages: 4
Thermaltake Extreme Spirit Il Instruction preview
Extreme Spirit Il
Brand: Thermaltake Pages: 2
Rockwell Automation Trusted T8833 Manual preview
Trusted T8833
Brand: Rockwell Automation Pages: 21
Antec KÜHLER H2O 920 Software Manual preview
KÜHLER H2O 920
Brand: Antec Pages: 6
Knowles IA611 Xplained Pro User Manual preview
IA611 Xplained Pro
Brand: Knowles Pages: 14
ICOP Technology VDX-6354RD User Manual preview
VDX-6354RD
Brand: ICOP Technology Pages: 42
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Brand: Digital Equipment Pages: 90
ADLINK Technology EOS-1200 User Manual preview
EOS-1200
Brand: ADLINK Technology Pages: 108
Forcepoint V10000 G4R2 Quick Start Manual preview
V10000 G4R2
Brand: Forcepoint Pages: 2
Cypress Semiconductor CY7C1480V25 Specification Sheet preview
CY7C1480V25
Brand: Cypress Semiconductor Pages: 32
Delta Electronics Suppression Inductors LFZ24H Specification Sheet preview
Suppression Inductors LFZ24H
Brand: Delta Electronics Pages: 1
AMD B59 User Manual preview
B59
Brand: AMD Pages: 10
Omnitron Systems Technology iConverter GX/F User Manual preview
iConverter GX/F
Brand: Omnitron Systems Technology Pages: 2
Cambium Networks PMP 430 Series User Manual preview
PMP 430 Series
Brand: Cambium Networks Pages: 132

Brands by name

Popular brands

Load more brands