manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

555 

 

 

Figure 17-59. Input capture logic 

CI0

Synchronizer

D

Prescaler

Capture 

Register

（

CH0VAL

）

Clock 

Prescaler

Counter

TIMER_CK

Q

Filter

D

Q

D

Q

Edge Detector

ITS 

CH0MS

CH0IF

CH0IE

CH0_CC_I

TIMERx_CC_I NT

Capture  INT From  Other Channal

CH0CAPPSC

Edge selector

&inverter

Based on 

CH0P&CH0NP

CI0FE0

Rising/Falling

ITI0

ITI3

ITI1
ITI2

CI0FED

Rising&Falling

IS0 

CI0FED

 

Channels’ input signals (CIx) is the TIMERx_CHx signal. First, the channel input signal (CIx) 
is synchronized to TIMER_CK domain, and then sampled by a  digital filter to generate a 
filtered input signal. Then through the edge detector, the rising and falling edge are detected. 
You can select one of them by CHxP. One more selector is for the other channel and trig, 
controlled by CHxMS. The IC_prescaler make several the input event generate one effective 
capture event. On the capture event, CHxVAL will restore the value of Counter.   

So the process can be divided to several steps as below:    

Step1

: Filter configuration. (CHxCAPFLT  in TIMERx_CHCTL0)   

            Based  on  the  input  signal  and  requested  signal  quality,  configure  compatible 
CHxCAPFLT.   

Step2

: Edge selection. (CHxP/CHxNP in TIMERx_CHCTL2) 

            Rising or falling edge, choose one by CHxP/CHxNP.  

Step3

: Capture source selection. (CHxMS in TIMERx_CHCTL0) 

As soon as you select one input capture source by CHxMS, you have set the channel 

to input mode ( CHxMS!=0x0) and TIMERx_CHxCV cannot be written any more.  

Step4

: Interrupt enable. (CHxIE and CHxDEN in TIMERx_DMAINTEN) 

            Enable the related interrupt enable; you can got the interrupt and DMA request.   

Step5

: Capture enables. (CHxEN in TIMERx_CHCTL2) 

Result

:   

when you wanted input signal is got, TIMERx_CHxCV will be set by counter’s value. 

And CHxIF is asserted. If the CHxIF is high, the CHxOF will be asserted also. The interrupt 

and  DMA request will  be  asserted based on  the  configuration of  CHxIE and  CHxDEN  in 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

dbx 902 Manual preview
902
Brand: dbx Pages: 8
NAIM AV2 Update Instructions preview
AV2
Brand: NAIM Pages: 2
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
LSI MegaRAID SCSI 320-2X Quick Installation Manual preview
MegaRAID SCSI 320-2X
Brand: LSI Pages: 4
Taiwan Commate Computer Inc. S630MA Quick Installation preview
S630MA
Brand: Taiwan Commate Computer Inc. Pages: 29
Wintech TDS510USB Plus Installation Manual preview
TDS510USB Plus
Brand: Wintech Pages: 21
Renesas Converter Board R0E5212BACFG00 User Manual preview
Converter Board R0E5212BACFG00
Brand: Renesas Pages: 6
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Brand: ICP DAS USA Pages: 8
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Brand: Qlogic Pages: 8
ZALMAN ZM-RF1 User Manual preview
ZM-RF1
Brand: ZALMAN Pages: 5
4gon RouterBOARD 411R Quick Start Manual preview
RouterBOARD 411R
Brand: 4gon Pages: 2
Digi ConnectCore 8X Hardware Reference Manual preview
ConnectCore 8X
Brand: Digi Pages: 116
Supersonic Franky Instruction Manual preview
Franky
Brand: Supersonic Pages: 46
C-Smartlink DMH25 Manual preview
DMH25
Brand: C-Smartlink Pages: 7
Loopcomm LP-8014 Quick Start Manual preview
LP-8014
Brand: Loopcomm Pages: 2
Cooler Master Masterliquid ML240L RGB Manual preview
Masterliquid ML240L RGB
Brand: Cooler Master Pages: 18
ekwb EK-Quantum Vector FTW3 RTX 2080 Ti Installation Manual preview
EK-Quantum Vector FTW3 RTX 2080 Ti
Brand: ekwb Pages: 3
ekwb 3831109810316 User Manual preview
3831109810316
Brand: ekwb Pages: 16

Brands by name

Popular brands

Load more brands