GigaDevice Semiconductor GD32VF103 User Manual Download Page 418

Page: 418 / 536

GD32VF103 User Manual

418

19.3.3.

External device address mapping

Figure 19-2. EXMC memory banks

Bank0(4x64M)

0x6000 0000

0x6FFF FFFF

Address

Banks

Supported memory type

NOR/PSRAM

EXMC access space is divided into one bank. Bank0 is 4*64 Mbytes. The first bank (Bank0)

is further divided into 4 Regions, which is 64 Mbytes (only Bank0 Region0 is used).

Each bank or region has a separate chip-select control signal, which can be configured

independently.

Bank0 is used for NOR and PSRAM device access.

NOR/PSRAM address mapping

Figure 19-3. Region of bank0 address mapping

reflects the address mapping of the region

of bank0. Internal AHB address lines HADDR[27:26] bits are used to select the region, but

only region0 is supported.

Figure 19-3. Region of bank0 address mapping

Region0

0x60000000

NOR/PSRAM

HADDR[27:26]

Address

Regions

Supported memory type

0x63FFFFFF

HADDR[25:0] is the byte address whereas the external memory may not be byte accessed,

this will lead to address inconsistency. EXMC can adjust HADDR to accommodate the data

width of the external memory according to the following rules.

–

When data bus width of the external memory is 8-bits. In this case the memory address

is byte aligned. HADDR[25:0] is connected to EXMC_A[25:0] and then the EXMC_A[25:0]

is connected to the external memory address lines.

–

When data bus width of the external memory is 16-bits. In this case the memory address

is half-word aligned. HADDR byte address must be converted into half-word aligned by

connecting HADDR[25:1] with EXMC_A[24:0]. The EXMC_A[24:0] is connected to the

external memory address lines.

19.3.4.

NOR/PSRAM controller

NOR/PSRAM memory controller controls bank0, which is designed to support NOR Flash,

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands