GigaDevice Semiconductor GD32VF103 User Manual Download Page 22

Page: 22 / 536

GD32VF103 User Manual

System and memory architecture

The devices of GD32VF103 series are 32-bit general-purpose microcontrollers based on the

32bit RISC-V processor. The RISC-V processor includes three AHB buses known as I-Code

bus, D-Code bus and System buse. All memory accesses of the RISC-V processor are

executed on the three buses according to the different purposes and the target memory

spaces. The memory organization uses a Harvard architecture, pre-defined memory map and

up to 4 GB of memory space, making the system flexible and extendable.

1.1.

RISC-V CPU

RISC-V CPU target for embedded applications that require low energy consumption and small

area, which is compliant to RISC-V architecture with several efficient micro-architecture

features, including simple dynamic branch prediction, instruction pre-fetch buffers and local

memories. It supports 32 general purpose registers (GPRs) and fast multiplier for

performance/area tradeoff:



RISC-V compliant little-endian RV32IMAC (32GPRs) ;



Configurable 2-stage pipeline optimized for low gate-count and high frequency;



Machine (M) and User (U) Privilege levels support;



Single-cycle hardware multiplier and Multi-cycles hardware divider support;



Misaligned load/store hardware support;



Atomic instructions hardware support;



Non-maskable interrupt (NMI) support;



Dynamic Branch Prediction and instruction pre-fetch buffers to speed up control code;



State-of-the-art micro-architecture design to tradeoff area and performance

requirements;



WFI (Wait for Interrupt) support;



WFE (Wait for Event) support;



Interrupt priority levels configurable and programmable;



Enhancement of vectored interrupt handling for real-time performance;



Support interrupt preemption with priority ;



Support interrupt tail chaining;



Standard 4-wire JTAG debug port



Support interactive debug functionalities



Support 4 triggers for hardware breakpoint

1.2.

System architecture

A 32-bit multilayer bus is implemented in the

GD32VF103 devices, which makes the parallel

access paths between multiple masters and slaves in the system possible The multilayer bus

consists of an AHB interconnect matrix, one AHB bus and two APB buses. The

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands