manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, User Manual

Introducing the GigaDevice Semiconductor GD32F20 Series - a cutting-edge product with exceptional features. Unlock the full potential of your device by accessing the comprehensive User Manual, available for free download at manualshive.com. This manual is your ultimate guide to harnessing the power of GD32F20, ensuring optimal performance and user satisfaction.

Share
Download
background image

 

                                                                                                             

GD32F20x User Manual

 

202 

 

plaintext is also obtained after data swapping according to the data type. The procedure of 

AES CBC mode decryption is illustrated in 

Figure 10-11. AES CBC decryption

. 

Figure 10-11. AES CBC decryption 

SWAP

CAU_DI

DATAM

AEA, decrypt

CAU_KEY0..3

SWAP

CAU_DO

Ciphertext

Plaintext

CAU_IV0..1(H/L)

+

 

AES-CTR mode 

In  counter  mode,  a  counter  is  used  in  addition  with  a  nonce  value  to  be  encrypted  and 

decrypted in AEA, and the result will be used for the XOR operation with the plaintext or the 

ciphertext.  As  the  counter  is  incremented  from  the  same  initialized  value  for  each  block  in 

encryption  and  decryption,  the  key  schedule  during  the  encryption  and  decryption  are  the 

same. Then decryption operation acts exactly in the same way as the encryption operation. 

Only the 32-bit LSB of the 128-bit initialization vector represents the counter, which means 

the other 96 bits are unchanged during the operation, and the initial value should be set to 1. 

Nonce is 32-bit single-use random value and should be updated to each communication block. 

And the 64-bit initialization vector is used to ensure that a given value is used only once for a 

given key. 

Figure 10-12. Counter block structure

 illustrates the counter block structure and 

Figure 10-13. AES CTR encryption/decryption

 shows the AES CTR encryption/decryption. 

Figure 10-12. Counter block structure 

NONCE

Initialization 

vector

Counter

 

Figure 10-13. AES CTR encryption/decryption 

 

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F20 Series

S-COM 7K Manual preview
7K
Brand: S-COM Pages: 400
AUMA GSTI 25.1 Operating Instructions Manual preview
GSTI 25.1
Brand: AUMA Pages: 24
ICS Tunnel Master Jr User Manual preview
Tunnel Master Jr
Brand: ICS Pages: 70
DAYLIFF SUNVERTER B Installation & Operating Manual preview
SUNVERTER B
Brand: DAYLIFF Pages: 40
Dieffematic LINEA c400 Instructions And Recommendations For The Installer preview
LINEA c400
Brand: Dieffematic Pages: 9
M-system EAR70 Instruction Manual preview
EAR70
Brand: M-system Pages: 8
S&S Northern Merlin 500S User Manual preview
Merlin 500S
Brand: S&S Northern Pages: 8
A.O. Smith INTELLI-VENT Troubleshooting Manual preview
INTELLI-VENT
Brand: A.O. Smith Pages: 46
Phocos CIS05-2L User Manual preview
CIS05-2L
Brand: Phocos Pages: 2
Coremorrow Modular E70 Series User Manual preview
Modular E70 Series
Brand: Coremorrow Pages: 14
ICP DAS USA Compact Embedded Controller LinPAC-8x41 Hardware User Manual preview
Compact Embedded Controller LinPAC-8x41
Brand: ICP DAS USA Pages: 13
Viking MLC-24 Technical Practice preview
MLC-24
Brand: Viking Pages: 4
SRS Labs RMC12, RMC8 Instruction Manual preview
RMC12, RMC8
Brand: SRS Labs Pages: 16
Erreka VU2A31 Installer Manual preview
VU2A31
Brand: Erreka Pages: 24
NEC N8103-197 Notes On Use preview
N8103-197
Brand: NEC Pages: 6
Eaton 9315P Installation And Operation Manual preview
9315P
Brand: Eaton Pages: 62
National Instruments PCI-7352 Getting Started preview
PCI-7352
Brand: National Instruments Pages: 40
National Instruments PCI-7354 Getting Started preview
PCI-7354
Brand: National Instruments Pages: 40

Brands by name

Popular brands

Load more brands