manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

460

 

 

5. 

After the transmission of the first byte, the TBE bit will be set, the software can write the 
third byte to the I2C_DATA register and TBE is cleared. After this, any time TBE is set, 
software can write a byte to I2C_DATA as long as there is still data to be transmitted. 

6. 

During  the  transmission  of  the  second  last  byte,  software  writes  the  last  data  to 
I2C_DATA to clear the TBE flag and doesn’t care TBE anymore. So TBE will be set after 
the byte’s transmission and not cleared until a STOP signal. 

I2C master doesn’t acknowledge to the last byte according to the I2C protocol, so after 
sending the last byte, I2C slave will wait for the STOP signal on I2C bus and sets AERR 
(Acknowledge  Error)  bit  to  notify  software  that  the  transmission  completes.  Software 
clears AERR bit by writing 0 to it. 

Figure 17-9. Programming model for slave transmitting mode (10-bit address mode) 

IDLE

Master generates START 

condition

Master sends Address

Slave sends Acknowledge

Master generates repeated 

START condition

Master sends header

Slave sends Acknowledge

SCL stretched by slave

Slave sends DATA(1)

Master sends Acknowledge

……

（

Data transmission

）

Slave sends  DATA(N-2)

Master sends Acknowledge

Slave sends  DATA(N)

Master DON'T send Ack

Master generates STOP 

condition

1) Software initialization

Set ADDSEND

2) Clear ADDSEND

Set ADDSEND

2) Clear ADDSEND

Set TBE

Set TBE

Set TBE

Set AERR

Clear TBE

3) Write DATA(1) to TRB

   Write DATA(x) to TRB

Set TBE

4) Write DATA(2) to TRB

5) Write DATA(3) to TRB

6)Write DATA(N) to TRB

Slave sends  DATA(N-1)

Master sends Acknowledge

Set TBE

7) Clear AERR

I2C Line State

Hardware Action

Software Flow

Master sends Header

Slave sends Acknowledge

 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

DayTronic 3700 Series Instruction Manual preview
3700 Series
Brand: DayTronic Pages: 22
Federal Signal Corporation UltraVoice Installation, Operation And Service Manual preview
UltraVoice
Brand: Federal Signal Corporation Pages: 60
FASTRON. VC-210 Installation And Operating Instructions Manual preview
VC-210
Brand: FASTRON. Pages: 16
Dahua DHI-ARC3008C User Manual preview
DHI-ARC3008C
Brand: Dahua Pages: 137
SOMFY Situo 1 RTS Manual preview
Situo 1 RTS
Brand: SOMFY Pages: 4
SYCLOPE TRACE'O Manual preview
TRACE'O
Brand: SYCLOPE Pages: 60
Airlow CP Touch User Manual preview
CP Touch
Brand: Airlow Pages: 20
Vageo RT-1 Manual preview
RT-1
Brand: Vageo Pages: 2
DirectConnect VC70DSW Instructions preview
VC70DSW
Brand: DirectConnect Pages: 2
Qorvo ACT88326 Manual preview
ACT88326
Brand: Qorvo Pages: 45
YASKAWA MP3100 Series Instructions Manual preview
MP3100 Series
Brand: YASKAWA Pages: 25
E-T-A ControlPlex CPC12 T Series User Manual preview
ControlPlex CPC12 T Series
Brand: E-T-A Pages: 30
InPlay IN1BN-DKC0-100-C0 User Manual preview
IN1BN-DKC0-100-C0
Brand: InPlay Pages: 11
Trio MC508 P848 Quick Start Manual preview
MC508 P848
Brand: Trio Pages: 8
thomann Botex DMX RDM Tester User Manual preview
Botex DMX RDM Tester
Brand: thomann Pages: 80
Famco MONT72 Series User Manual preview
MONT72 Series
Brand: Famco Pages: 113
Proxy Mobile Reader Pro User Manual preview
Mobile Reader Pro
Brand: Proxy Pages: 15
Cooper & Hunter LH-13001 Manual preview
LH-13001
Brand: Cooper & Hunter Pages: 6

Brands by name

Popular brands

Load more brands